EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

TiO2-Coated Fiber-Optic Sensor for Monitoring Ambient pH Fabricated Using the Sol–Gel Method

Ulises González-Vázquez, Lizeth Rojas-Blanco, Marcela del Carmen Arellano-Cortaza, Ildefonso Zamudio-Torres, Erika Viviana Miranda-Mandujano, Rubén Alejandro Vázquez-Sánchez, Erik Ramirez-Morales

Crystals · 20.08.2026 · 16 (8) · 543

DOI: 10.3390/cryst16080543 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 20.08.2026. Verfasst von Ulises González-Vázquez und 6 weiteren Autor:innen. Die Arbeit nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: SECIHTI, Semiconductor Laboratory, UJAT.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Environmental pollution, particularly water contamination, requires the continuous development of robust, effective monitoring technologies. While chemical optical sensors offer significant advantages for environmental monitoring, many traditional devices rely on complex combinations of chemical dyes with specific acid dissociation constants. To overcome these limitations, this study presents a dye-free approach centered on a fiber-optic pH sensor based on a TiO2 thin film. The protective coating of multimode optical fibers was successfully removed using a controlled hydrofluoric acid (HF) treatment, enabling deposition of TiO2 films via a low-cost sol–gel dip-coating method. Structural characterizations through X-ray diffraction (XRD) and Raman spectroscopy confirmed the preferential growth and high purity of the anatase phase. Furthermore, energy-dispersive X-ray spectroscopy (EDS) confirmed the presence and relatively uniform distribution of Ti on the fiber surface. The optical performance of the sensor was evaluated using a 940 nm light source over a broad pH range (4–14), where the device exhibited distinguishable stepped optical-power responses at four pH conditions spanning pH 4–14. A preliminary analysis yielded an apparent average slope of 0.40 µW/pH. These results support the feasibility of using sol–gel derived TiO2 coatings in the preliminary development of dye-free optical devices for aqueous pH monitoring.

Förderung

  • SECIHTI
  • Semiconductor Laboratory
  • UJAT

Zitieren

APA

González-Vázquez, U., Rojas-Blanco, L., Arellano-Cortaza, M. D. C., Zamudio-Torres, I., Miranda-Mandujano, E. V., Vázquez-Sánchez, R. A., & Ramirez-Morales, E. (2026). TiO2-Coated Fiber-Optic Sensor for Monitoring Ambient pH Fabricated Using the Sol–Gel Method. Crystals, 16(8), 543. https://doi.org/10.3390/cryst16080543

Vancouver

González-Vázquez U, Rojas-Blanco L, Arellano-Cortaza MDC, Zamudio-Torres I, Miranda-Mandujano EV, Vázquez-Sánchez RA, et al. TiO2-Coated Fiber-Optic Sensor for Monitoring Ambient pH Fabricated Using the Sol–Gel Method. Crystals. 2026;16(8):543. doi:10.3390/cryst16080543

BibTeX
@article{GonzlezVzquez2026,
  author = {González-Vázquez, Ulises and Rojas-Blanco, Lizeth and Arellano-Cortaza, Marcela del Carmen and Zamudio-Torres, Ildefonso and Miranda-Mandujano, Erika Viviana and Vázquez-Sánchez, Rubén Alejandro and Ramirez-Morales, Erik},
  title = {TiO2-Coated Fiber-Optic Sensor for Monitoring Ambient pH Fabricated Using the Sol–Gel Method},
  journal = {Crystals},
  year = {2026},
  volume = {16},
  number = {8},
  pages = {543},
  doi = {10.3390/cryst16080543}
}
Kostenlos starten →