EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Temperature Field and Phase Transformation Analysis in Friction Stir Additive Manufacturing of Aluminum-Lithium Alloys

Yixin Sun, Jie Zhang, Hai Gu, Zulei Liang, Jianhua Sun, Jie Jiang, Guoqing Dai, Bin Li, Zhonggang Sun

Crystals · 01.08.2026 · 16 (8) · 502

DOI: 10.3390/cryst16080502 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 01.08.2026. Verfasst von Yixin Sun und 8 weiteren Autor:innen. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Major Project, Nantong Science and Technology Plan Project, Laser Processing and Metal Additive Manufacturing Technology and Application.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Al-Li alloys present significant challenges for conventional fusion-based additive manufacturing (AM) due to their low evaporation temperature and high reactivity with oxygen. As a solid-state process, friction stir additive manufacturing (FSAM) is expected to eliminate melting and solidification during processing, thereby overcoming these limitations. This study investigates the FSAM of 2195 Al-Li alloy through temperature measurements and numerical simulations. The research focuses on the temperature at the center of the deposited region and the phase evolution before and after FSAM. The results indicate that during FSAM, the temperature at the center of the deposited zone ranges from 458 to 497 °C. In terms of phase constitution, the T3-tempered alloy primarily consists of an α-Al matrix and the δ’ (Al3Li) phase. The T8-tempered alloy contains α-Al, θ’ (Al2Cu), and T1 (Al2CuLi) phases. In the nugget zone (NZ), the peak temperature exceeds 450 °C. As a result, the T1 and θ’ phases dissolve, leaving only a small amount of δ’/β’ precipitates. This study presents a preliminary investigation based on a single-layer FSAM process. These findings provide a foundation for optimizing FSAM process parameters for Al-Li alloys.

Förderung

  • National Science and Technology Major Project
  • Nantong Science and Technology Plan Project
  • Laser Processing and Metal Additive Manufacturing Technology and Application
  • “Qinglan Project” Funding for Higher Education Institutions in Jiangsu
  • International Cooperation Project of Jiangsu Province

Zitieren

APA

Sun, Y., Zhang, J., Gu, H., Liang, Z., Sun, J., Jiang, J., Dai, G., Li, B., & Sun, Z. (2026). Temperature Field and Phase Transformation Analysis in Friction Stir Additive Manufacturing of Aluminum-Lithium Alloys. Crystals, 16(8), 502. https://doi.org/10.3390/cryst16080502

Vancouver

Sun Y, Zhang J, Gu H, Liang Z, Sun J, Jiang J, et al. Temperature Field and Phase Transformation Analysis in Friction Stir Additive Manufacturing of Aluminum-Lithium Alloys. Crystals. 2026;16(8):502. doi:10.3390/cryst16080502

BibTeX
@article{Sun2026,
  author = {Sun, Yixin and Zhang, Jie and Gu, Hai and Liang, Zulei and Sun, Jianhua and Jiang, Jie and Dai, Guoqing and Li, Bin and Sun, Zhonggang},
  title = {Temperature Field and Phase Transformation Analysis in Friction Stir Additive Manufacturing of Aluminum-Lithium Alloys},
  journal = {Crystals},
  year = {2026},
  volume = {16},
  number = {8},
  pages = {502},
  doi = {10.3390/cryst16080502}
}
Kostenlos starten →