EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Silicon Content on Mechanical and Tribological Properties of FeSi Steels

Marcela Motýľová, Ivan Petrišinec, Róbert Džunda, Jana Andrejovská

Crystals · 22.11.2025 · 15 (12) · 1005

DOI: 10.3390/cryst15121005 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Crystals, online erschienen am 22.11.2025. Verfasst von Marcela Motýľová und 3 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: EU NextGenerationEU.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Non-oriented (NO) Fe–Si electrical steels are key materials for magnetic cores of electrical machines, requiring a balance between magnetic and mechanical properties. This study systematically examined the effect of silicon content (1.06 wt%, 2.15 wt%, and 3.09 wt%) on the microstructure, mechanical, and tribological behavior of three produced NO steel grades. Mechanical properties were assessed using tensile tests, microhardness, and nanoindentation, while tribological performance was evaluated under dry reciprocating sliding (ball-on-flat) against a 100Cr6 steel ball at loads of 5 N, 10 N, and 25 N. Increasing silicon content led to larger grain size, higher hardness (227 HV–361 HV) and strength, but lower ductility. Tribological behavior depended on both composition and load. The most stable friction regime occurred at 10 N. The medium-Si steel (N3, 2.15 wt%) exhibited the best performance with a low coefficient of friction (COF ≈ 0.52–0.55); N5 (3.09 wt%) showed a similar COF, while N1 (1.06 wt%) had a slightly higher value. At 25 N, an inverse relationship between hardness and friction appeared: softer N1 had the lowest COF (≈0.68–0.70), whereas harder N3 and N5 reached ≈ 0.74–0.78. Scanning electron microscopy (SEM) observations revealed abrasive wear for N3/N5 and plastic flow (galling) for N1. Overall, an optimal silicon content provides the best compromise between hardness and tribological stability depending on load conditions.

Förderung

  • EU NextGenerationEU

Zitieren

APA

Motýľová, M., Petrišinec, I., Džunda, R., & Andrejovská, J. (2025). Influence of Silicon Content on Mechanical and Tribological Properties of FeSi Steels. Crystals, 15(12), 1005. https://doi.org/10.3390/cryst15121005

Vancouver

Motýľová M, Petrišinec I, Džunda R, Andrejovská J. Influence of Silicon Content on Mechanical and Tribological Properties of FeSi Steels. Crystals. 2025;15(12):1005. doi:10.3390/cryst15121005

BibTeX
@article{Motov2025,
  author = {Motýľová, Marcela and Petrišinec, Ivan and Džunda, Róbert and Andrejovská, Jana},
  title = {Influence of Silicon Content on Mechanical and Tribological Properties of FeSi Steels},
  journal = {Crystals},
  year = {2025},
  volume = {15},
  number = {12},
  pages = {1005},
  doi = {10.3390/cryst15121005}
}
Kostenlos starten →