Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF
Crystals · 05.06.2023 · 13 (6) · 913
DOI: 10.3390/cryst13060913 ↗Kurz gefasst
Fachartikel in der Zeitschrift Crystals, online erschienen am 05.06.2023. Verfasst von Yuxian Lu und 8 weiteren Autor:innen. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, National Natural Science Foundation of China, Youth Innovation Promotion Association, CAS.
Abstract (Originalsprache)
Laser powder bed fusion (LPBF) is a typical additive manufacturing technology that offers significant advantages in the production of complex components. With the rapid heating and cooling characteristics of LPBF, a large amount of solid solution of alloying elements in the matrix can be achieved to form supersaturated solid solutions, thus enhancing the properties of LPBF alloys. For the unique microstructure, the heat treatment process needs to be adjusted accordingly. In this work, a Zr/Sc-modified Al-Mg alloy processed by laser powder bed fusion (LPBF) with relatively low cost and good mechanical properties was investigated. The fine microstructure was obtained under rapid solidification conditions. The nanoscale Al3(Sc,Zr) particles precipitated at the molten pool boundary during solidification. These particles, as effective heterogeneous nucleators, further refined the α-Al grains and improved the mechanical properties of the alloy. As a result, the alloy exhibited a heterogeneous microstructure consisting of columnar grains in the center of the molten pool and equiaxed grains at the boundaries. The rapid solidification resulted in the supersaturation of solute atoms in the α-Al matrix, which significantly enhanced the solid solution strengthening effect. With the LPBF processing parameters of a combination of a laser power of 250 W, a laser scanning speed of 833 mm/s, and stripe scanning mode, the tensile strength of the alloy reached 401.4 ± 5.7 MPa, which was significantly higher than that of the cast alloys with aging treatment (281.1 ± 1.3 MPa). The heat treatment promoted the formation of secondary Al3(Sc,Zr), Mn/Mg-rich phases. The ultimate tensile strength and elongation at fracture after aging at 325 °C for 2 h were 536.0 ± 1.7 MPa and 14.8 ± 0.8%, respectively. The results provide insight into the preparation of aluminum alloys with relatively low cost and excellent mechanical properties.
Förderung
- National Key Research and Development Program of China
- National Natural Science Foundation of China
- Youth Innovation Promotion Association, CAS
- Bintech-IMR R&D Program
Zitieren
APA
Lu, Y., Zhang, H., Xue, P., Wu, L., Liu, F., Jia, L., Ni, D., Xiao, B., & Ma, Z. (2023). Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF. Crystals, 13(6), 913. https://doi.org/10.3390/cryst13060913
Vancouver
Lu Y, Zhang H, Xue P, Wu L, Liu F, Jia L, et al. Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF. Crystals. 2023;13(6):913. doi:10.3390/cryst13060913
BibTeX
@article{Lu2023,
author = {Lu, Yuxian and Zhang, Hao and Xue, Peng and Wu, Lihui and Liu, Fengchao and Jia, Luanluan and Ni, Dingrui and Xiao, Bolv and Ma, Zongyi},
title = {Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF},
journal = {Crystals},
year = {2023},
volume = {13},
number = {6},
pages = {913},
doi = {10.3390/cryst13060913}
}
EUVIMED