EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Corrosion Behavior of N80 Steel Under Coalbed Methane Conditions

Jian Liu, Shijun Chen, Manxiang Li, Baojun Zheng, Chaoming Wang, Juantao Zhang, Ning Liu, Xiaofei Cao

Coatings · 20.08.2026 · 16 (8) · 993

DOI: 10.3390/coatings16080993 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 20.08.2026. Verfasst von Jian Liu und 7 weiteren Autor:innen. Die Arbeit nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Oil & Gas Major Project.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The corrosion behavior of N80 steel in a simulated coalbed–methane environment was investigated in a high-temperature, high-pressure autoclave. Uniform corrosion and maximum pit depth were quantified by weight-loss measurements and ultra-depth-of-field three-dimensional microscopy, respectively, while SEM, EDS, and XRD were used to characterize the morphology, elemental composition, and crystalline phases of the surface corrosion products. A one-factor-at-a-time design was applied at a constant total pressure of 10 MPa to evaluate the effects of nominal CO2 partial pressure (0.10–1.00 MPa), nominal O2 partial pressure (0–0.40 MPa), Cl− concentration (3–187 g/L), and temperature (40–75 °C). Increasing the nominal CO2 partial pressure raised the uniform corrosion rate from 0.712 to 0.930 mm/a but reduced the maximum pitting corrosion rate from 1.691 to 0.280 mm/a, while FeCO3-containing surface coverage increased. Increasing the nominal O2 partial pressure intensified both corrosion modes; at 0.40 MPa, the uniform and maximum pitting corrosion rates reached 1.446 and 2.202 mm/a, respectively, and the corrosion-product layer exhibited extensive cracking and spallation. Increasing the Cl− concentration reduced the uniform corrosion rate from 1.078 to 0.839 mm/a but increased the maximum pitting corrosion rate from 0.474 to 1.807 mm/a, indicating a shift in the principal damage risk from average metal loss to localized penetration. The uniform corrosion rate reached a maximum of 1.516 mm/a at 60 °C, whereas the maximum pitting corrosion rate increased continuously to 2.202 mm/a at 75 °C. XRD identified Fe, FeCO3, Fe2O3, Fe3O4, and FeOOH. The persistent Fe substrate reflections, interpreted together with the SEM observations, revealed spatially heterogeneous corrosion-product coverage. These results show that the protective contribution of FeCO3-containing products depends on their surface coverage and visible integrity rather than on phase presence alone. The findings support stringent oxygen-ingress control, targeted pitting protection in high-salinity environments, and enhanced corrosion surveillance of intermediate- and high-temperature well sections.

Förderung

  • Oil & Gas Major Project

Zitieren

APA

Liu, J., Chen, S., Li, M., Zheng, B., Wang, C., Zhang, J., Liu, N., & Cao, X. (2026). Corrosion Behavior of N80 Steel Under Coalbed Methane Conditions. Coatings, 16(8), 993. https://doi.org/10.3390/coatings16080993

Vancouver

Liu J, Chen S, Li M, Zheng B, Wang C, Zhang J, et al. Corrosion Behavior of N80 Steel Under Coalbed Methane Conditions. Coatings. 2026;16(8):993. doi:10.3390/coatings16080993

BibTeX
@article{Liu2026,
  author = {Liu, Jian and Chen, Shijun and Li, Manxiang and Zheng, Baojun and Wang, Chaoming and Zhang, Juantao and Liu, Ning and Cao, Xiaofei},
  title = {Corrosion Behavior of N80 Steel Under Coalbed Methane Conditions},
  journal = {Coatings},
  year = {2026},
  volume = {16},
  number = {8},
  pages = {993},
  doi = {10.3390/coatings16080993}
}
Kostenlos starten →