EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

HiPIMS-Deposited Nb/NbC/C Multilayer Coatings on 316L Stainless Steel for PEMFC Bipolar Plates

Xinjie Zhao, Lei He, Yi Xu, Guodong Li

Coatings · 13.06.2026 · 16 (6) · 707

DOI: 10.3390/coatings16060707 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 13.06.2026. Verfasst von Xinjie Zhao und 3 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In view of the fact that there are few reports on the preparation of NbC coating by high-power pulsed magnetron sputtering (HiPIMS) technology. In this study, the effects of NbC interlayer thickness on the microstructure, corrosion resistance and electrical conductivity of Nb/NbC/C multilayer coatings for proton exchange membrane fuel cell (PEMFC) bipolar plates were studied by using the high ionization characteristics of HiPIMS technology. A series of Nb/NbC/C multilayer coatings with varying NbC interlayer thicknesses was deposited via HiPIMS by modulating the deposition time (20, 40, and 60 min). The microstructure and properties of the coatings were characterized using scanning electron microscopy (SEM), Raman spectroscopy, interfacial contact resistance (ICR), and corrosion current, among other methods. The results indicate that as the NbC interlayer thickness increases, the total coating thickness increases from 0.43 μm to 1.42 μm. All coatings exhibit a uniform and dense microstructure lacking typical coarse columnar structures. Raman and XPS analyses show that the ID/IG ratio increases from 1.98 to 4.04, indicating an increase in sp2-hybridized bond content and a decrease in sp3 content. At a deposition time of 60 min, the coating achieved optimal performance, yielding a critical load (Lc1) of 31.9 N, the lowest average friction coefficient (0.27), the minimum corrosion current density, and an interfacial contact resistance of 7.5 mΩ·cm2. These results demonstrate that the NbC interlayer thickness significantly governs the structure and properties of the Nb/NbC/C multilayer coatings. Specifically, an appropriate increase in the NbC interlayer thickness optimizes the sp2/sp3 hybrid bond ratio, thereby enhancing the overall coating performance.

Zitieren

APA

Zhao, X., He, L., Xu, Y., & Li, G. (2026). HiPIMS-Deposited Nb/NbC/C Multilayer Coatings on 316L Stainless Steel for PEMFC Bipolar Plates. Coatings, 16(6), 707. https://doi.org/10.3390/coatings16060707

Vancouver

Zhao X, He L, Xu Y, Li G. HiPIMS-Deposited Nb/NbC/C Multilayer Coatings on 316L Stainless Steel for PEMFC Bipolar Plates. Coatings. 2026;16(6):707. doi:10.3390/coatings16060707

BibTeX
@article{Zhao2026,
  author = {Zhao, Xinjie and He, Lei and Xu, Yi and Li, Guodong},
  title = {HiPIMS-Deposited Nb/NbC/C Multilayer Coatings on 316L Stainless Steel for PEMFC Bipolar Plates},
  journal = {Coatings},
  year = {2026},
  volume = {16},
  number = {6},
  pages = {707},
  doi = {10.3390/coatings16060707}
}
Kostenlos starten →