EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface-Quality Optimisation in Cobalt Ferrite Ultrasonic Elliptical Vibration Cutting of H62 Brass

Yajue He, Zhihuang Shen, Shicong You, Xu Zhang, Junfeng Huang, Chaoshuai Qi

Coatings · 06.06.2026 · 16 (6) · 682

DOI: 10.3390/coatings16060682 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 06.06.2026. Verfasst von Yajue He und 5 weiteren Autor:innen. Die Arbeit nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Xiamen Municipal Natural Science Foundation, University-Industry Cooperation Project of Science and Technology Planning of Fujian Province, Challenge-Acceptance Project of Quanzhou City.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Cobalt ferrite (CoFe2O4) magnetostrictive ultrasonic elliptical vibration cutting (UEVC) tools have recently emerged as a low-cost, low-eddy-loss alternative to piezoelectric and rare-earth-driven cutting heads. The structural design and resonance characterisation of such a dual-bending CoFe2O4 UEVC tool was reported in our previous work. The present paper builds directly on that platform and addresses a different objective: to determine how the four primary process variables—feed rate, cutting speed, cutting depth, and inter-channel phase difference—should be set to obtain the best surface quality on a representative ductile metal. Using H62 brass as the workpiece and a single-crystal diamond tool with a 0.2 mm nose radius and 60° included angle, single-factor experiments are run on a custom 5-axis precision lathe, and surface roughness is mapped in both the cutting and the feed direction with a Keyence VK-X1000 confocal microscope (Keyence, Osaka, Japan). The speed ratio K = Vc/(2πfA) is computed for every test point so that each result can be classified as belonging to the continuous-contact or to the intermittent-contact UEVC regime. The results show: (i) feed rate has a non-monotonic effect, with an optimum at 1 μm where ductile-mode separation is achieved without secondary tool-trajectory overlap, reducing the cutting direction roughness by up to 45% with respect to conventional cutting (CC); (ii) the UEVC advantage shrinks at high cutting speeds because the speed ratio approaches unity and the intermittent regime collapses, but is still 12.6%–38% over the 50–375 mm/s range tested; (iii) the relative improvement is largest at low depth and decreases as the depth grows, retaining 11.5%–49% gain over CC across 0.5–10 μm; (iv) the inter-channel phase difference, which controls the geometry of the tool-tip ellipse, is the strongest single lever—at 60°, the trajectory becomes an oblique ellipse whose major axis is tilted with respect to the cutting direction, bringing the cutting direction roughness down to 1.21 μm against 2.82 μm for CC, a 57% reduction. A simple kinematic argument links this optimum to a maximum effective separation duration per cycle and offers a design rule for analogous UEVC tools.

Förderung

  • Xiamen Municipal Natural Science Foundation
  • University-Industry Cooperation Project of Science and Technology Planning of Fujian Province
  • Challenge-Acceptance Project of Quanzhou City

Zitieren

APA

He, Y., Shen, Z., You, S., Zhang, X., Huang, J., & Qi, C. (2026). Surface-Quality Optimisation in Cobalt Ferrite Ultrasonic Elliptical Vibration Cutting of H62 Brass. Coatings, 16(6), 682. https://doi.org/10.3390/coatings16060682

Vancouver

He Y, Shen Z, You S, Zhang X, Huang J, Qi C. Surface-Quality Optimisation in Cobalt Ferrite Ultrasonic Elliptical Vibration Cutting of H62 Brass. Coatings. 2026;16(6):682. doi:10.3390/coatings16060682

BibTeX
@article{He2026,
  author = {He, Yajue and Shen, Zhihuang and You, Shicong and Zhang, Xu and Huang, Junfeng and Qi, Chaoshuai},
  title = {Surface-Quality Optimisation in Cobalt Ferrite Ultrasonic Elliptical Vibration Cutting of H62 Brass},
  journal = {Coatings},
  year = {2026},
  volume = {16},
  number = {6},
  pages = {682},
  doi = {10.3390/coatings16060682}
}
Kostenlos starten →