EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Mechanical Properties of CVD TiN/TiB2 Multilayer Coatings

Nina Schalk, Michael Tkadletz, Alexandra Lechner, Martin Krobath, Jozef Keckes, Juraj Todt, Manfred Burghammer, Bernhard Sartory, Werner Ecker, Christoph Czettl

Coatings · 24.03.2026 · 16 (4) · 394

DOI: 10.3390/coatings16040394 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 24.03.2026. Verfasst von Nina Schalk und 9 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Austrian Federal Ministry of Labor and Economy, National Foundation for Research, Technology and Development and the Christian Doppler Research Association, COMET programme within the K2 Center.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Chemical vapor deposited (CVD) TiN and TiB2 are both commonly used as wear-resistant hard coatings. The two materials exhibit pronounced differences in their properties, which can be exploited by combining them in a multilayer architecture. Thus, two multilayer coatings with different bilayer periodicities of ~80 and ~220 nm were synthesized. The multilayer architecture constrains the TiN grain size to dimensions comparable to the individual sublayer thickness, which are substantially smaller than those observed in the single-layer TiN reference coating. This grain refinement leads to significantly higher hardness of the TiN sublayers within the multilayer system compared to the single-layer coating. In contrast, the low grain size of the TiB2 coating appears unaffected, and the hardness of the TiB2 layers in the multilayer and corresponding bilayer reference coating is also comparable. The compressive residual stress in the TiB2 layers decreases with decreasing layer thickness, while the tensile residual stress in the TiN layers increases, resulting in a roughly constant stress difference between the sublayers, which is also comparable to the conventional TiN/TiB2 bilayer reference coating. However, while the tensile stress in the TiN sublayers is constant over coating thickness, TiB2 exhibits a pronounced gradient with only low compressive stress at the interface to the substrate, which increases significantly with increasing coating thickness. The fracture properties of the multilayers range between the values obtained for the corresponding reference coatings. Complementary finite element method simulations revealed that, for the multilayer coatings, the common assumption of a stress-free state of micro-cantilevers used for bending tests is not valid.

Förderung

  • Austrian Federal Ministry of Labor and Economy
  • National Foundation for Research, Technology and Development and the Christian Doppler Research Association
  • COMET programme within the K2 Center
  • “Integrated Computational Material, Process and Product Engineering”

Zitieren

APA

Schalk, N., Tkadletz, M., Lechner, A., Krobath, M., Keckes, J., Todt, J., Burghammer, M., Sartory, B., Ecker, W., & Czettl, C. (2026). Microstructure and Mechanical Properties of CVD TiN/TiB2 Multilayer Coatings. Coatings, 16(4), 394. https://doi.org/10.3390/coatings16040394

Vancouver

Schalk N, Tkadletz M, Lechner A, Krobath M, Keckes J, Todt J, et al. Microstructure and Mechanical Properties of CVD TiN/TiB2 Multilayer Coatings. Coatings. 2026;16(4):394. doi:10.3390/coatings16040394

BibTeX
@article{Schalk2026,
  author = {Schalk, Nina and Tkadletz, Michael and Lechner, Alexandra and Krobath, Martin and Keckes, Jozef and Todt, Juraj and Burghammer, Manfred and Sartory, Bernhard and Ecker, Werner and Czettl, Christoph},
  title = {Microstructure and Mechanical Properties of CVD TiN/TiB2 Multilayer Coatings},
  journal = {Coatings},
  year = {2026},
  volume = {16},
  number = {4},
  pages = {394},
  doi = {10.3390/coatings16040394}
}
Kostenlos starten →