Crack Propagation Mechanism in Thermal Barrier Coatings Containing Different Residual Grit Particles Under Thermal Cycling
Coatings · 23.06.2025 · 15 (7) · 747
DOI: 10.3390/coatings15070747 ↗Kurz gefasst
Fachartikel in der Zeitschrift Coatings, online erschienen am 23.06.2025. Verfasst von Xin Shen und 9 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Sichuan Science and Technology Program, Open Research Project of State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment, Open Fund Project of National United Engineering Laboratory for Advanced Bearing Tribology.
Abstract (Originalsprache)
Residual particles embedded at the bond coat/substrate (BC/SUB) interface after grit blasting can affect the failure behavior of thermal barrier coatings (TBCs) under thermal cycling. This study employed a 2D finite element model combining the cohesive zone method (CZM) and extended finite element method (XFEM) to analyze the effect of interfacial grit particles. Specifically, the CZM was used to simulate crack propagation at the BC/thermally grown oxide (TGO) interface, while XFEM was applied to model the arbitrary crack propagation within the BC layer. Three models were analyzed: no grit inclusion, 20 μm grit particles, and 50 μm grit particles at the BC/SUB interface. This systematic variation allowed isolating the influence of particle size on the location of crack propagation onset, stress distribution, and crack growth behavior. The results showed that grit particles at the SUB/BC interface had negligible influence on the crack propagation location and rate at the BC/TGO interface, due to their spatial separation. However, their presence significantly altered the radial tensile stress distribution within the BC layer. Larger grit particles induced more intense stress concentrations and promoted earlier and more extensive vertical crack propagation within the BC. However, due to plastic deformation and stress redistribution in the BC, the crack propagation was progressively suppressed in the later stages of thermal cycling. Overall, grit particles primarily promoted vertical crack propagation within the BC layer. Optimizing grit blasting to control grit particle size is crucial for improving the durability of TBCs.
Förderung
- Sichuan Science and Technology Program
- Open Research Project of State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment
- Open Fund Project of National United Engineering Laboratory for Advanced Bearing Tribology
- Postgraduate Innovation Fund Project by Southwest University of Science and Technology
- Doctoral Scientific Research Foundation of Hubei University of Automotive Technology
- construction project of the Fujiang Laboratory Nuclear Medicine Artificial Intelligence Research Center
Zitieren
APA
Shen, X., Wei, Z., Jiang, Z., Zhang, J., Li, D., Gong, X., Li, Q., Zhao, F., Lai, J., & Yu, J. (2025). Crack Propagation Mechanism in Thermal Barrier Coatings Containing Different Residual Grit Particles Under Thermal Cycling. Coatings, 15(7), 747. https://doi.org/10.3390/coatings15070747
Vancouver
Shen X, Wei Z, Jiang Z, Zhang J, Li D, Gong X, et al. Crack Propagation Mechanism in Thermal Barrier Coatings Containing Different Residual Grit Particles Under Thermal Cycling. Coatings. 2025;15(7):747. doi:10.3390/coatings15070747
BibTeX
@article{Shen2025,
author = {Shen, Xin and Wei, Zhiyuan and Jiang, Zhenghao and Zhang, Jianpu and Li, Dingjun and Gong, Xiufang and Li, Qiyuan and Zhao, Fei and Lai, Jianping and Yu, Jiaxin},
title = {Crack Propagation Mechanism in Thermal Barrier Coatings Containing Different Residual Grit Particles Under Thermal Cycling},
journal = {Coatings},
year = {2025},
volume = {15},
number = {7},
pages = {747},
doi = {10.3390/coatings15070747}
}
EUVIMED