EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Verification of the Simulated Carburizing Process in Different Bore Sizes

András Rumony, Attila Szlancsik, Dorina Kovács

Coatings · 31.05.2023 · 13 (6) · 1019

DOI: 10.3390/coatings13061019 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Coatings, online erschienen am 31.05.2023. Verfasst von András Rumony und 2 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Research, Development and Innovation Office (NKFIH), the ÚNKP-22-5-BME-308 New National Excellence Program of the Ministry for Culture and Innovation, the Ministry of Culture and Innovation of Hungary from the National Research, Development and Innovation Fund.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Carburizing is one of the leading surface treatments in the industry. For this study, 20MnCr5 steel was gas carburized and quenched in real circumstances and simulated with Simufact software. The research investigated the dimensions and types of bores. A through and blind bore was used in this study to analyze how the geometry affects the created layer and, additionally, it takes into account the placement in the heat treatment furnace. An optical microscope and Vickers hardness tester were used to detect the changes in microstructure and measure the layer thickness. After the experiments, a simulation calculated the same variables to compare and validate the results to each other. It can be stated that the placement in the chamber did not influence the form of the high carbon content layer. The simulation and the measured results were in good agreement. The maximum hardness difference was 17%, but the calculated layer thicknesses were always between the measured data. For example, in the case of a small blind bore, the calculated layer thickness was 1.68 ± 0.18 mm, while the measured value was 1.54 ± 0.37 mm. Additionally, the hardness change in depth was similar in both cases. After this validation process, the residual stresses and plastic strains were determined. The maximum residual stresses were similar for every case, namely around 1900 MPa, while the maximum plastic strain was measured in a small blind bore with a value of 0.18. The minimum plastic strain was 0.04 in the through bore.

Förderung

  • the National Research, Development and Innovation Office (NKFIH)
  • the ÚNKP-22-5-BME-308 New National Excellence Program of the Ministry for Culture and Innovation
  • the Ministry of Culture and Innovation of Hungary from the National Research, Development and Innovation Fund

Zitieren

APA

Rumony, A., Szlancsik, A., & Kovács, D. (2023). Verification of the Simulated Carburizing Process in Different Bore Sizes. Coatings, 13(6), 1019. https://doi.org/10.3390/coatings13061019

Vancouver

Rumony A, Szlancsik A, Kovács D. Verification of the Simulated Carburizing Process in Different Bore Sizes. Coatings. 2023;13(6):1019. doi:10.3390/coatings13061019

BibTeX
@article{Rumony2023,
  author = {Rumony, András and Szlancsik, Attila and Kovács, Dorina},
  title = {Verification of the Simulated Carburizing Process in Different Bore Sizes},
  journal = {Coatings},
  year = {2023},
  volume = {13},
  number = {6},
  pages = {1019},
  doi = {10.3390/coatings13061019}
}
Kostenlos starten →