Sustainable Congo Red Removal Using Pyrolysis-Engineered Zeolite–Chitosan Composites: Adsorption Modeling, Regeneration, and Electrocatalytic Reuse
Catalysts · 19.11.2026 · 16 (11) · 1041
DOI: 10.3390/catal16111041 ↗Kurz gefasst
Fachartikel in der Zeitschrift Catalysts, online erschienen am 19.11.2026. Verfasst von Rehab Mahmoud und 6 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Natural zeolite–chitosan (ZT–CS) composites incorporating Ni2+, pyrolyzed at 500 °C and 800 °C (ZT–CS−500 and ZT–CS−800), were developed as lowcost, regenerable adsorbents for the removal of Congo red (CR) dye from water and evaluated using Box–Behnken optimization, advanced monolayer statistical−physics modeling, and spent−adsorbent valorization assessment. Pyrolysis reduced the BET surface area from 62.976 m2 g−1 (ZT–CS) to 55.424 and 36.197 m2 g−1 for ZT–CS−500 and ZT–CS−800, respectively, while increasing the average pore diameter to 33.568 nm and generating NiO/NiAl2O4 phases. Batch adsorption followed pseudo−second−order kinetics (qe = 165.45, 42.66 and 413.08 mg g−1 for ZT–CS, ZT–CS−500 and ZT–CS−800, respectively), and equilibrium data at 25 °C gave Langmuir maximum capacities (qmax) of 383.8, 232.5 and 774.3 mg g−1, increasing to 478.55 and 2069.5 mg g−1 for ZT–CS−500 and ZT–CS−800, respectively, at 55 °C, confirming an endothermic, thermally enhanced uptake process. Advanced monolayer statistical−physics modeling (R2 > 0.99) yielded a near−unity stoichiometric coefficient (n ≈ 0.77–0.78), a monolayer site density (Nm) of 1373.4–1439.8 mg g−1, and an adsorption energy (ΔE) of 11.30–12.46 kJ mol−1, which is consistent with a predominantly physisorption-governed, spontaneous, thermally promoted mechanism reinforced by Ni-associated chemisorption. Response−surface (Box–Behnken) optimization revealed a pH of 3, an adsorbent dose of 0.001 g, and a contact time of 92.5 min as the optimal conditions for ZT–CS-800, with a predicted removal efficiency of 95.86% (model R2 = 0.9843, adjusted R2 = 0.9641, F = 48.71); the pH had the greatest influence on removal (F = 166.23), followed by the contact time (F = 124.57) and adsorbent dose (F = 32.48). ZT–CS−800 retained 92.4% of its initial adsorption capacity (2287.5 vs. 2475.0 mg g−1) and 91.5% CR removal after five adsorption–desorption cycles, with the desorption efficiency remaining above 93%, outperforming ZT–CS−500 (73.7% capacity retention). The estimated production cost of the composites ranged from USD 0.0126–0.0130 g−1, and a scale−up assessment revealed that only 41–141 g of ZT–CS-800 was required per 100 L of effluent to achieve 80–95% CR removal. These results establish ZT–CS-800 as a low-cost, high-capacity, and reusable adsorbent for the treatment of CR-contaminated wastewater, with additional potential for post-adsorption electrocatalytic valorization. The incorporation of CR into the ZT–CS composite enhanced the electrochemical performance. Cyclic voltammetry revealed that the maximum current density of the ZT–CS–CR-800 electrode reached 214.32 mA cm−2, whereas that of the ZT–CS electrode was 45.17 mA cm−2. Electrochemical impedance spectroscopy confirmed the superior charge-transfer resistance of ZT–CS–CR (3.97 Ω) relative to that of ZT–CS (50.92 Ω), corroborating the enhanced interfacial electron−transfer kinetics. stability of the electrodes retained 76.35% (ZT–CS) and 97.36% (ZT–CS–CR−800) over 3600 s of continuous operation, confirming adequate electrochemical durability. These findings demonstrate that CR incorporation and a suitable temperature effectively modify the electrode–electrolyte interfacial properties, accelerate charge−transfer kinetics, and increase catalytic activity, positioning ZT–CS–CR as a promising candidate for urea electro-oxidation in fuel-cell applications.
Zitieren
APA
Mahmoud, R., Radalla, A. M., Mohamed, E. A., Mohamed, H., Elsuccary, S. A. A., Al-Olayan, E., & Mahgoub, S. M. (2026). Sustainable Congo Red Removal Using Pyrolysis-Engineered Zeolite–Chitosan Composites: Adsorption Modeling, Regeneration, and Electrocatalytic Reuse. Catalysts, 16(11), 1041. https://doi.org/10.3390/catal16111041
Vancouver
Mahmoud R, Radalla AM, Mohamed EA, Mohamed H, Elsuccary SAA, Al-Olayan E, et al. Sustainable Congo Red Removal Using Pyrolysis-Engineered Zeolite–Chitosan Composites: Adsorption Modeling, Regeneration, and Electrocatalytic Reuse. Catalysts. 2026;16(11):1041. doi:10.3390/catal16111041
BibTeX
@article{Mahmoud2026,
author = {Mahmoud, Rehab and Radalla, Abdelatty M. and Mohamed, Eman A. and Mohamed, Hala and Elsuccary, Saber A. A. and Al-Olayan, Ebtesam and Mahgoub, Samar M.},
title = {Sustainable Congo Red Removal Using Pyrolysis-Engineered Zeolite–Chitosan Composites: Adsorption Modeling, Regeneration, and Electrocatalytic Reuse},
journal = {Catalysts},
year = {2026},
volume = {16},
number = {11},
pages = {1041},
doi = {10.3390/catal16111041}
}
EUVIMED