Effect of Extrusion Binder on the Structure and Propane Dehydrogenation Performance of Pt-Sn Catalyst Bodies
Catalysts · 16.11.2026 · 16 (11) · 1019
DOI: 10.3390/catal16111019 ↗Kurz gefasst
Fachartikel in der Zeitschrift Catalysts, online erschienen am 16.11.2026. Verfasst von Irmak Su Okten Acar und 5 weiteren Autor:innen. Die Arbeit nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union’s Horizon 2020 research and innovation programme, TÜBİTAK 2244 University–Industry Cooperation Project.
Abstract (Originalsprache)
Pt-Sn catalysts for propane dehydrogenation (PDH) have been widely studied in powder form; however, the combined effects of binder type and content on the shapeability, structural integrity, and catalytic behavior of extruded Pt-Sn catalysts for PDH remain largely unexplored. Commercial γ-Al2O3 and hydrotalcite-derived Mg(Al)O pellets were compared with hydrotalcite-rich extruded bodies formulated using boehmite-derived alumina or sepiolite binders. The results revealed that binder selection affected extrusion feasibility, pore architecture, mechanical strength (crushing strengths of 3.0–15.0 N/mm for the selected extrudates), and the radial distribution of the metal phase. Among the investigated systems, the hydrotalcite-derived Mg(Al)O reference exhibited the most favorable PDH performance (~30% propane conversion, close to equilibrium, with an apparent ~4% activity loss over 12 h), while the γ-Al2O3-supported catalyst showed the lowest propane conversion and selectivity. The extruded composites delivered intermediate performance, and increasing the boehmite content from 10 to 30 wt.% increased the coking rate fivefold. Notably, the hydrotalcite–sepiolite catalyst maintained stable conversion and ~94% propylene selectivity despite a higher coking rate, which TEM-EDX associated with coke deposition on the support rather than on the Pt-Sn particles. Overall, binder selection is a key factor controlling the structural, mechanical, and catalytic properties of extruded Pt-Sn catalyst bodies and reveals a trade-off between mechanical integrity and catalytic performance.
Förderung
- European Union’s Horizon 2020 research and innovation programme
- TÜBİTAK 2244 University–Industry Cooperation Project
Zitieren
APA
Acar, I. S. O., Is, G., Celebi, S., Savacı, U., Turan, S., & Aciksari, C. (2026). Effect of Extrusion Binder on the Structure and Propane Dehydrogenation Performance of Pt-Sn Catalyst Bodies. Catalysts, 16(11), 1019. https://doi.org/10.3390/catal16111019
Vancouver
Acar ISO, Is G, Celebi S, Savacı U, Turan S, Aciksari C. Effect of Extrusion Binder on the Structure and Propane Dehydrogenation Performance of Pt-Sn Catalyst Bodies. Catalysts. 2026;16(11):1019. doi:10.3390/catal16111019
BibTeX
@article{Acar2026,
author = {Acar, Irmak Su Okten and Is, Gizem and Celebi, Serdar and Savacı, Umut and Turan, Servet and Aciksari, Cem},
title = {Effect of Extrusion Binder on the Structure and Propane Dehydrogenation Performance of Pt-Sn Catalyst Bodies},
journal = {Catalysts},
year = {2026},
volume = {16},
number = {11},
pages = {1019},
doi = {10.3390/catal16111019}
}
EUVIMED