EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Practical Calculation Method and Influencing Parameter Analysis of Main Cable Geometry for Long-Span Asymmetric Suspension Bridges

Qiuya Wang, Yichen Wang, Qinxi Dong, Kunpeng Zhao, Zengwu Liu, Yongfang Zhou, Yingke Liu, Ruixue Chen

Buildings · 09.05.2026 · 16 (10) · 1883

DOI: 10.3390/buildings16101883 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Buildings, online erschienen am 09.05.2026. Verfasst von Qiuya Wang und 7 weiteren Autor:innen. Die Arbeit nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Doctoral Start-up Foundation of Shandong Jiaotong University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aiming at the problems of main cable geometry calculation and control accuracy in construction for long-span asymmetric suspension bridges, this paper proposes a practical method for main cable geometry calculation of asymmetric suspension bridges based on the Rushankou Bridge. Firstly, a hanger–pylon–girder model was established to obtain the constraint force at the hanger top. Then, with the mid-span sag of the main cable set as the control target, the coordinates and unstressed length of the main cable in the completed bridge state were obtained based on the pylon–cable model. Finally, the final main cable geometry and unstressed length were obtained based on the main cable–hanger–pylon–girder model. The reliability of the method in this paper was validated by engineering monitoring data. Using the simulation model, the influence laws and degrees of parameters including temperature, main cable elastic modulus, main cable weight, hanger force and main girder weight on the main cable geometry were investigated. It is indicated that the method in this paper is capable of accurately calculating the main cable shape of asymmetric suspension bridges. After the installation of cable clamps and hangers, the theoretical and measured deformations of the main cable are in good agreement. The theoretical and measured values at the mid-span L/2 of the main span are −233.9 cm and −234.7 cm, respectively, with a deviation of 8 mm. The largest discrepancy between the calculated and actual deformations of the main cable is located at 7L/8 of the main span, which is merely 2.2 cm. The deformation of the main cable is greatly affected by temperature changes; each 1 °C temperature variation leads to a mid-span deformation of about 2.4 cm in the main cable. If the influence of temperature variation on main cable geometry is ignored during construction, it will cause errors in the main cable elevation after installation. The effect of the main cable elastic modulus on its deformation cannot be neglected, and a 10% variation in the main cable elastic modulus leads to a 58 cm change in the main cable geometry.

Förderung

  • Doctoral Start-up Foundation of Shandong Jiaotong University

Zitieren

APA

Wang, Q., Wang, Y., Dong, Q., Zhao, K., Liu, Z., Zhou, Y., Liu, Y., & Chen, R. (2026). Practical Calculation Method and Influencing Parameter Analysis of Main Cable Geometry for Long-Span Asymmetric Suspension Bridges. Buildings, 16(10), 1883. https://doi.org/10.3390/buildings16101883

Vancouver

Wang Q, Wang Y, Dong Q, Zhao K, Liu Z, Zhou Y, et al. Practical Calculation Method and Influencing Parameter Analysis of Main Cable Geometry for Long-Span Asymmetric Suspension Bridges. Buildings. 2026;16(10):1883. doi:10.3390/buildings16101883

BibTeX
@article{Wang2026,
  author = {Wang, Qiuya and Wang, Yichen and Dong, Qinxi and Zhao, Kunpeng and Liu, Zengwu and Zhou, Yongfang and Liu, Yingke and Chen, Ruixue},
  title = {Practical Calculation Method and Influencing Parameter Analysis of Main Cable Geometry for Long-Span Asymmetric Suspension Bridges},
  journal = {Buildings},
  year = {2026},
  volume = {16},
  number = {10},
  pages = {1883},
  doi = {10.3390/buildings16101883}
}
Kostenlos starten →