Bioinspired Origami Morphing Limbs for Amphibious Robot Locomotion
Biomimetics · 17.07.2026 · 11 (7) · 502
DOI: 10.3390/biomimetics11070502 ↗Kurz gefasst
Fachartikel in der Zeitschrift Biomimetics, online erschienen am 17.07.2026. Verfasst von Yuxuan Li und 4 weiteren Autor:innen. Beteiligte Einrichtung: Center for Mechanics Plus under Extreme Environments, School of Mechanics and Engineering Science, Ningbo University, Ningbo 315211, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Ningbo City, Graduate Student Scientific Research and Innovation Project of Ningbo University.
Abstract (Originalsprache)
Amphibious robots must reconcile two distinct mechanical requirements within a compact locomotion architecture. Terrestrial operation requires limb structures with sufficient load-bearing capacity, contact stability, and bending resistance, whereas aquatic operation benefits from a larger projected area for drag-based thrust generation. Conventional amphibious platforms often address these requirements by combining separate land and water propulsion modules, which increases structural redundancy, system mass, and hydrodynamic resistance. To reduce this conflict at the structural level, this study proposes a bioinspired origami morphing limb based on a modified Yoshimura pattern. The limb transforms between a closed cylindrical configuration for terrestrial support and an unfolded planar configuration for aquatic paddling. A vertex-splitting topology and thick-panel geometric constraints are introduced to suppress the bifurcation instability associated with the zero-thickness Yoshimura vertex, thereby obtaining a deterministic single-degree-of-freedom folding path suitable for robotic actuation. A screw-theory-based kinematic model is established to relate the active driving angle to the passive folding angle, and geometric parameter analysis is used to connect the folding state with load-bearing and paddling morphologies. A quadruped amphibious robot prototype is fabricated using rigid polylactic acid panels and flexible thermoplastic polyurethane hinges. Prototype-level observations qualitatively demonstrate reversible transformation within the tested operating range and show walking, crawling, rolling, water-entry, and underwater locomotion modes.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Center for Mechanics Plus under Extreme Environments, School of Mechanics and Engineering Science, Ningbo University, Ningbo 315211, China.
- Piezoelectric Device Laboratory, School of Mechanics and Engineering Science, Ningbo University, Ningbo 315211, China.
Förderung
- National Natural Science Foundation of China
- Natural Science Foundation of Ningbo City
- Graduate Student Scientific Research and Innovation Project of Ningbo University
- Ningbo University
Zitieren
APA
Li, Y., Mei, S., Yin, R., Liu, C., & Chen, H. (2026). Bioinspired Origami Morphing Limbs for Amphibious Robot Locomotion. Biomimetics, 11(7), 502. https://doi.org/10.3390/biomimetics11070502
Vancouver
Li Y, Mei S, Yin R, Liu C, Chen H. Bioinspired Origami Morphing Limbs for Amphibious Robot Locomotion. Biomimetics. 2026;11(7):502. doi:10.3390/biomimetics11070502
BibTeX
@article{Li2026,
author = {Li, Yuxuan and Mei, Siyu and Yin, Rensong and Liu, Chong and Chen, Hui},
title = {Bioinspired Origami Morphing Limbs for Amphibious Robot Locomotion},
journal = {Biomimetics},
year = {2026},
volume = {11},
number = {7},
pages = {502},
doi = {10.3390/biomimetics11070502}
}
EUVIMED