EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Synergistic Strengthening and Toughening of 3D-Printed Bioinspired Alumina Composites with a Multi-Scale Bouligand Structure

Zhaozhi Wang, Dongxu Duan, Lei Yang, Xu Bai, Zhibin Jiao, Chenliang Wu, Jing Zhao, Zhihui Zhang

Biomimetics · 06.04.2026 · 11 (4) · 252

DOI: 10.3390/biomimetics11040252 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomimetics, online erschienen am 06.04.2026. Verfasst von Zhaozhi Wang und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Shenyang University of Technology, Shenyang 110870, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Liaoning Provincial Science and Technology Program Joint Fund, National Nature Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Inspired by the Bouligand helicoidal architecture of the dactyl club of the peacock mantis shrimp, this study employed direct ink writing (DIW) 3D printing to construct a three-level synergistic toughening system composed of nano-SiO2, microscale flake alumina, and a macroscale helicoidal structure. The effects of nano-SiO2 content, Bouligand helix angle, and flake alumina content on the flexural strength and fracture toughness of the composite ceramics were systematically investigated. The results showed that the optimal nano-SiO2 addition was 7 wt%, yielding a fracture toughness of 1.03 MPa·m1/2, which was 13% higher than that of pure alumina. The introduced intergranular glassy phase transformed the rigid grain-boundary bonding into a moderately strong gradient interface, resulting in higher fracture toughness for all SiO2-containing samples than for pure alumina. The Bouligand structure further increased the fracture toughness to a maximum of 1.45 MPa·m1/2 at a helix angle of 10°, representing a 39% improvement over the 0° sample. When microscale flake alumina was incorporated into the optimal matrix containing 7 wt% SiO2, the best overall mechanical performance was achieved at a flake alumina content of 5 wt%, where the flakes directly dissipated fracture energy through pull-out, fracture, and bridging mechanisms. The synergistic effect of the three structural levels was most pronounced at a helix angle of 20°, at which the sample containing 5 wt% flake alumina achieved a fracture toughness of 2.07 MPa·m1/2 with almost no loss in flexural strength, corresponding to a 113% improvement over the sample without flake alumina. These results demonstrate that three-level synergy can be achieved through nanoscale interfacial optimization, microscale energy dissipation by reinforcing phases, and macroscale crack deflection induced by the helicoidal structure, thereby providing important theoretical and experimental support for the multiscale design of high-performance bioinspired ceramic materials.

Schlagwörter

Stichwörter der Autor:innen

Bouligand structuredirect ink writingfracture toughnessmultiscale reinforcement

Autor:innen und Institutionen

  • School of Mechanical Engineering, Shenyang University of Technology, Shenyang 110870, China.
  • School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870, China.
  • Key Laboratory of Bionic Engineering (Ministry of Education), Jilin University, Changchun 130022, China.
  • Institute of Structured and Architected Materials, Liaoning Academy of Materials, Shenyang 110167, China.

Förderung

  • National Natural Science Foundation of China
  • Liaoning Provincial Science and Technology Program Joint Fund
  • National Nature Science Foundation of China

Zitieren

APA

Wang, Z., Duan, D., Yang, L., Bai, X., Jiao, Z., Wu, C., Zhao, J., & Zhang, Z. (2026). Synergistic Strengthening and Toughening of 3D-Printed Bioinspired Alumina Composites with a Multi-Scale Bouligand Structure. Biomimetics, 11(4), 252. https://doi.org/10.3390/biomimetics11040252

Vancouver

Wang Z, Duan D, Yang L, Bai X, Jiao Z, Wu C, et al. Synergistic Strengthening and Toughening of 3D-Printed Bioinspired Alumina Composites with a Multi-Scale Bouligand Structure. Biomimetics. 2026;11(4):252. doi:10.3390/biomimetics11040252

BibTeX
@article{Wang2026,
  author = {Wang, Zhaozhi and Duan, Dongxu and Yang, Lei and Bai, Xu and Jiao, Zhibin and Wu, Chenliang and Zhao, Jing and Zhang, Zhihui},
  title = {Synergistic Strengthening and Toughening of 3D-Printed Bioinspired Alumina Composites with a Multi-Scale Bouligand Structure},
  journal = {Biomimetics},
  year = {2026},
  volume = {11},
  number = {4},
  pages = {252},
  doi = {10.3390/biomimetics11040252}
}
Kostenlos starten →