EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Compressive Strength Optimization of 3D-Printed Voronoi Trabecular Bone Using the Taguchi Method

Suyeon Seo iD, Ju-Hee Lee iD, Minchae Kang iD, Eunsol Park, Min-Woo Han

Biomimetics · 31.12.2025 · 11 (1) · 20

DOI: 10.3390/biomimetics11010020 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomimetics, online erschienen am 31.12.2025. Verfasst von Suyeon Seo und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Dongguk University, 30 Pildong-ro 1, Jung-gu, Seoul 04620, Republic of Korea. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and ICT, Korean government.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The surge in demand for patient-specific orthopedic implants necessitates the precise optimization of design and processing parameters for artificial trabecular bone. This research utilizes Voronoi-based porous structures to replicate the irregular geometry characteristic of natural trabecular bone. All specimens were fabricated through fused deposition modeling (FDM) with polylactic acid (PLA). The study systematically investigated the influence of four primary parameters, namely build orientation, extruder temperature, layer height, and pore count, on compressive strength. To ensure experimental efficiency, the research implemented a Taguchi L20 orthogonal array. Subsequent signal-to-noise (S/N) ratio analysis identified the optimal parameter set as a y-90° build orientation, an extruder temperature of 200 °C, a layer height of 0.2 mm, and a count of 150 pores. These findings underscore the necessity of integrated geometric and process parameter optimization to advance additive manufacturing for orthopedic applications.

Schlagwörter

Stichwörter der Autor:innen

3D printingTaguchi methodVoronoi structureadditive manufacturing (AM)compressive strengthfused deposition modeling (FDM)parameter optimizationtrabecular bone

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Dongguk University, 30 Pildong-ro 1, Jung-gu, Seoul 04620, Republic of Korea.
  • Department of Mechanical, Robotics and Energy Engineering, Dongguk University, 30 Pildong-ro 1, Jung-gu, Seoul 04620, Republic of Korea.

ORCID-Profile: Suyeon Seo, Ju-Hee Lee, Minchae Kang

Förderung

  • Ministry of Science and ICT
  • Korean government

Zitieren

APA

Seo, S., Lee, J. H., Kang, M., Park, E., & Han, M. W. (2025). Compressive Strength Optimization of 3D-Printed Voronoi Trabecular Bone Using the Taguchi Method. Biomimetics, 11(1), 20. https://doi.org/10.3390/biomimetics11010020

Vancouver

Seo S, Lee JH, Kang M, Park E, Han MW. Compressive Strength Optimization of 3D-Printed Voronoi Trabecular Bone Using the Taguchi Method. Biomimetics. 2025;11(1):20. doi:10.3390/biomimetics11010020

BibTeX
@article{Seo2025,
  author = {Seo, Suyeon and Lee, Ju-Hee and Kang, Minchae and Park, Eunsol and Han, Min-Woo},
  title = {Compressive Strength Optimization of 3D-Printed Voronoi Trabecular Bone Using the Taguchi Method},
  journal = {Biomimetics},
  year = {2025},
  volume = {11},
  number = {1},
  pages = {20},
  doi = {10.3390/biomimetics11010020}
}
Kostenlos starten →