EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Axis Change on Shrinkage Rate of 3D-Printed Bioceramic Zirconia Fabricated via Digital Light Processing

Ju-Young Park iD, Yoo-Na Jung, Kyoung-Jun Jang, Sang-Kyu Lee, Seong-Won Choi, Yong-Seok Lee iD, Yunzhi Peter Yang iD, Kwi-Dug Yun iD

Biomimetics · 25.02.2025 · 10 (3) · 140

DOI: 10.3390/biomimetics10030140 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biomimetics, online erschienen am 25.02.2025. Verfasst von Ju-Young Park und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, Chonnam National University, Gwangju 61186, Republic of Korea. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea (NRF) funded by the ministry of Trade, Industry and Energy, National Research Foundation of Korea (NRF).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Isotropic shrinkage is critical for producing dimensionally accurate prostheses using zirconia. However, the anisotropic shrinkage of 3D-printed zirconia limits its utility in clinical applications. We aimed to evaluate the impact of specimen axis alterations on the shrinkage of digital light processing (DLP)-printed zirconia. Cubes measuring 10 × 10 × 10 mm3 (similar in size to molar crowns) and cuboids measuring 10 × 10 × 20 mm (similar in size to a three-unit bridge) were manufactured using a DLP 3D printer. Zirconia specimens were pre-sintered at 1300 °C and 1400 °C. The Z-axis of some specimens was switched to the X-axis before the final sintering procedure. The X-axis, Y-axis, and Z-axis lengths of the green body, pre-sintered block, and fully sintered block were measured using digital calipers. The 3D-printed specimens showed lower shrinkage and higher deviation than the milled specimens, whose shrinkage rate was 26%. The shrinkage rates of the 3D-printed cubic specimens were 19.9% (length), 20.0% (width), and 21.99% (height), while those of the cuboidal specimens were 20.26%, 19.72%, and 21.81%, respectively. For the 3D-printed specimens, which shrink anisotropically during sintering, the axis change step had no significant impact on the shrinkage rate. In all groups, the shrinkage rate along the building direction during printing significantly exceeded that along the gravity direction during sintering.

Schlagwörter

Stichwörter der Autor:innen

3D-printed zirconiaanisotropicdigital fixed prosthodonticsshrinkage rate

Autor:innen und Institutionen

  • Department of Prosthodontics, School of Dentistry, Chonnam National University, Gwangju 61186, Republic of Korea.
  • Research Institute, 3D Controls Co., Ltd., Busan 46721, Republic of Korea.
  • Industry Support Center for Convergence Medical Devices, Chonnam National University Hospital, Gwangju 61469, Republic of Korea.
  • Department of Mechanical Engineering, Myongji University, Yongin 17058, Republic of Korea.
  • Department of Orthopedic Surgery, School of Medicine, Stanford University, Stanford, CA 94305, USA.
  • Department of Materials Science and Engineering, School of Engineering, Stanford University, Stanford, CA 94305, USA.

ORCID-Profile: Ju-Young Park, Yong-Seok Lee, Yunzhi Peter Yang, Kwi-Dug Yun

Förderung

  • National Research Foundation of Korea (NRF) funded by the ministry of Trade, Industry and Energy
  • National Research Foundation of Korea (NRF)

Zitieren

APA

Park, J. Y., Jung, Y. N., Jang, K. J., Lee, S. K., Choi, S. W., Lee, Y. S., Yang, Y. P., & Yun, K. D. (2025). Effect of Axis Change on Shrinkage Rate of 3D-Printed Bioceramic Zirconia Fabricated via Digital Light Processing. Biomimetics, 10(3), 140. https://doi.org/10.3390/biomimetics10030140

Vancouver

Park JY, Jung YN, Jang KJ, Lee SK, Choi SW, Lee YS, et al. Effect of Axis Change on Shrinkage Rate of 3D-Printed Bioceramic Zirconia Fabricated via Digital Light Processing. Biomimetics. 2025;10(3):140. doi:10.3390/biomimetics10030140

BibTeX
@article{Park2025,
  author = {Park, Ju-Young and Jung, Yoo-Na and Jang, Kyoung-Jun and Lee, Sang-Kyu and Choi, Seong-Won and Lee, Yong-Seok and Yang, Yunzhi Peter and Yun, Kwi-Dug},
  title = {Effect of Axis Change on Shrinkage Rate of 3D-Printed Bioceramic Zirconia Fabricated via Digital Light Processing},
  journal = {Biomimetics},
  year = {2025},
  volume = {10},
  number = {3},
  pages = {140},
  doi = {10.3390/biomimetics10030140}
}
Kostenlos starten →