EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Graft Bending Angle on the Tensile Behavior of Bone Tunnel-Graft Constructs for Anterior Cruciate Ligament Reconstruction Using Bone-Patellar Tendon–Bone Graft

Satoshi Yamakawa, Konsei Shino, Tomoki Ohori iD, Ken Nakata

Bioengineering · 26.06.2026 · 13 (7) · 752

DOI: 10.3390/bioengineering13070752 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioengineering, online erschienen am 26.06.2026. Verfasst von Satoshi Yamakawa und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Health and Sport Sciences, Medicine for Sports and Performing Arts, Graduate School of Medicine, The University of Osaka, Osaka 565-087…. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Japan Society for the Promotion of Science.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bone–patellar tendon–bone (BPTB) grafts used in anterior cruciate ligament reconstruction bend at the femoral tunnel aperture, forming a graft bending angle (GBA). However, the mechanical effects of GBA-related angled loading on bone–BPTB graft constructs remain unclear. This study investigated the effects of GBA and cyclic tensile loading on stiffness and elongation using porcine BPTB grafts. Fourteen specimens were assigned to tibial bone plug constructs (Type T, n = 7) or patellar bone plug constructs (Type P, n = 7). Each construct was cyclically loaded between 10 and 50 N for 50 cycles under GBA conditions of 0°, 30°, 60°, and 90°. Regardless of GBA condition, cyclic loading produced substantial increases in stiffness and elongation during the first 10 cycles, followed by smaller changes. Stiffness tended to decrease under greater GBA conditions, particularly in Type T constructs, where 60° and 90° reduced stiffness and increased elongation. Type P stiffness showed little dependence on GBA. At 0° and 30°, Type P showed lower stiffness and greater elongation than Type T. These findings indicate that bone–BPTB graft tensile behavior is governed by GBA-related loading geometry and bone plug–tendon junction morphology.

Schlagwörter

Stichwörter der Autor:innen

anterior cruciate ligament reconstructionbone–patellar tendon–bone graftgraft bending anglemechanical propertiestendon insertion angle

Autor:innen und Institutionen

  • Department of Health and Sport Sciences, Medicine for Sports and Performing Arts, Graduate School of Medicine, The University of Osaka, Osaka 565-0871, Japan.
  • Sports Orthopaedic Center, Yukioka Hospital, 2-2-3 Ukita, Osaka 530-0021, Japan.
  • Department of Orthopaedic Surgery, Graduate School of Medicine, The University of Osaka, Osaka 565-0871, Japan.

ORCID-Profile: Tomoki Ohori

Förderung

  • Japan Society for the Promotion of Science

Zitieren

APA

Yamakawa, S., Shino, K., Ohori, T., & Nakata, K. (2026). Effects of Graft Bending Angle on the Tensile Behavior of Bone Tunnel-Graft Constructs for Anterior Cruciate Ligament Reconstruction Using Bone-Patellar Tendon–Bone Graft. Bioengineering, 13(7), 752. https://doi.org/10.3390/bioengineering13070752

Vancouver

Yamakawa S, Shino K, Ohori T, Nakata K. Effects of Graft Bending Angle on the Tensile Behavior of Bone Tunnel-Graft Constructs for Anterior Cruciate Ligament Reconstruction Using Bone-Patellar Tendon–Bone Graft. Bioengineering. 2026;13(7):752. doi:10.3390/bioengineering13070752

BibTeX
@article{Yamakawa2026,
  author = {Yamakawa, Satoshi and Shino, Konsei and Ohori, Tomoki and Nakata, Ken},
  title = {Effects of Graft Bending Angle on the Tensile Behavior of Bone Tunnel-Graft Constructs for Anterior Cruciate Ligament Reconstruction Using Bone-Patellar Tendon–Bone Graft},
  journal = {Bioengineering},
  year = {2026},
  volume = {13},
  number = {7},
  pages = {752},
  doi = {10.3390/bioengineering13070752}
}
Kostenlos starten →