EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Wearing Layer Influences Long-Term Material Loss from Composite Floats for Oyster Aquaculture: An Accelerated-Weathering Comparison of Eight Candidate Materials

So Youn Mun, Pilseong Jang, Jun Hwan Jang

Aquaculture Journal · 09.11.2026 · 6 (4) · 56

DOI: 10.3390/aquacj6040056 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Aquaculture Journal, online erschienen am 09.11.2026. Verfasst von So Youn Mun und 2 weiteren Autor:innen. Die Arbeit nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Oceans and Fisheries.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Expanded polystyrene floats have been identified as a significant source of marine microplastic in oyster aquaculture, yet no certification criterion assesses the material that the certified alternatives shed. Gravimetric mass loss, normalised to a common exposed area of 7200 mm2, is reported under accredited accelerated weathering to KS F 2274 for eight float materials: expanded polystyrene at three densities, expanded polypropylene, three injection-moulded polymers, and a continuous-fibre basalt-reinforced thermoplastic composite. Specimens were dried to constant mass before weighing, so the quantity measured is a net change: an upper bound on particulate release, not a measure of it. Mass exceeded the initial value in all three stabilised expanded polypropylene specimens. At 3000 h the loss spanned a factor of 54, and every foamed material exceeded every non-foamed one, while tripling the density of expanded polystyrene reduced loss by only 25% (n = 3; p < 0.0001 across the foamed groups). For ten injection-moulded grades the accelerated ranking reproduced that of 2.5 years outdoors (Spearman ρ = 0.89), though the ratio varied from 0.4 to 6.3. A wear model indicates that the pure-polymer barrier providing water tightness contains 905–1180 g L−1 of polymer against 578 g L−1 for the laminate beneath, so the wearing layer, not the bulk material, may govern release in service.

Förderung

  • Ministry of Oceans and Fisheries

Zitieren

APA

Mun, S. Y., Jang, P., & Jang, J. H. (2026). The Wearing Layer Influences Long-Term Material Loss from Composite Floats for Oyster Aquaculture: An Accelerated-Weathering Comparison of Eight Candidate Materials. Aquaculture Journal, 6(4), 56. https://doi.org/10.3390/aquacj6040056

Vancouver

Mun SY, Jang P, Jang JH. The Wearing Layer Influences Long-Term Material Loss from Composite Floats for Oyster Aquaculture: An Accelerated-Weathering Comparison of Eight Candidate Materials. Aquaculture Journal. 2026;6(4):56. doi:10.3390/aquacj6040056

BibTeX
@article{Mun2026,
  author = {Mun, So Youn and Jang, Pilseong and Jang, Jun Hwan},
  title = {The Wearing Layer Influences Long-Term Material Loss from Composite Floats for Oyster Aquaculture: An Accelerated-Weathering Comparison of Eight Candidate Materials},
  journal = {Aquaculture Journal},
  year = {2026},
  volume = {6},
  number = {4},
  pages = {56},
  doi = {10.3390/aquacj6040056}
}
Kostenlos starten →