EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Dimensional and Surface Quality Evaluation of Inconel 718 Alloy After Grinding with Environmentally Friendly Cooling-Lubrication Technique and Graphene Enriched Cutting Fluid

Déborah de Oliveira, Raphael Lima de Paiva, Mayara Fernanda Pereira, Rosenda Valdés Arencibia, Rogerio Valentim Gelamo, Rosemar Batista da Silva

Applied Mechanics · 02.07.2025 · 6 (3) · 50

DOI: 10.3390/applmech6030050 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Mechanics, online erschienen am 02.07.2025. Verfasst von Déborah de Oliveira und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Council for Scientific and Technological Development, Minas Gerais state.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Properly refrigerating hard-to-cut alloys during grinding is key to achieve high quality, strict tolerances, and good surface finishing. Nonetheless, literature about the influence of cooling-lubrication conditions (CLCs) on dimensional accuracy of ground components is still scarce. Thus, this work aims to evaluate surface quality, grinding power, and dimensional accuracy of Inconel 718 workpieces after grinding with silicon carbide grinding wheel at different grinding conditions. Four different CLCs were tested: flood, minimum quantity of lubrication (MQL) without graphene, and with multilayer graphene (MG) at two distinct concentrations: 0.05 and 0.10 wt.%. Different radial depths of cut values were also tested. The results showed that the material’s removed height increased with radial depth of cut, leading to coarse tolerance (IT) grades. Machining with the MQL WG resulted in higher dimensional precision with an IT grade varying between IT6 and IT7, followed by MQL MG 0.10% (IT7), MQL MG 0.05% (IT7-IT8), and flood (IT8). The lower tolerances achieved with MG were attributed to the lowering in the friction coefficient of the workpiece material sliding through the abrasive grits with no material removal (micro-plowing mechanism), thereby reducing grinding power and the removed height in comparison to the other CLC tested.

Förderung

  • National Council for Scientific and Technological Development
  • Minas Gerais state

Zitieren

APA

Oliveira, D. D., Paiva, R. L. D., Pereira, M. F., Arencibia, R. V., Gelamo, R. V., & Silva, R. B. D. (2025). Dimensional and Surface Quality Evaluation of Inconel 718 Alloy After Grinding with Environmentally Friendly Cooling-Lubrication Technique and Graphene Enriched Cutting Fluid. Applied Mechanics, 6(3), 50. https://doi.org/10.3390/applmech6030050

Vancouver

Oliveira DD, Paiva RLD, Pereira MF, Arencibia RV, Gelamo RV, Silva RBD. Dimensional and Surface Quality Evaluation of Inconel 718 Alloy After Grinding with Environmentally Friendly Cooling-Lubrication Technique and Graphene Enriched Cutting Fluid. Applied Mechanics. 2025;6(3):50. doi:10.3390/applmech6030050

BibTeX
@article{Oliveira2025,
  author = {Oliveira, Déborah de and Paiva, Raphael Lima de and Pereira, Mayara Fernanda and Arencibia, Rosenda Valdés and Gelamo, Rogerio Valentim and Silva, Rosemar Batista da},
  title = {Dimensional and Surface Quality Evaluation of Inconel 718 Alloy After Grinding with Environmentally Friendly Cooling-Lubrication Technique and Graphene Enriched Cutting Fluid},
  journal = {Applied Mechanics},
  year = {2025},
  volume = {6},
  number = {3},
  pages = {50},
  doi = {10.3390/applmech6030050}
}
Kostenlos starten →