A Design Method for Hydraulic Oscillator Excitation Parameters Considering Drilling Conditions and Formation Characteristics
Applied Sciences · 12.03.2026 · 16 (6) · 2705
DOI: 10.3390/app16062705 ↗Kurz gefasst
Fachartikel in der Zeitschrift Applied Sciences, online erschienen am 12.03.2026. Verfasst von Xin He und 6 weiteren Autor:innen. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Intelligent Magnetic Guidance and Dynamic Risk Prevention for Large Platforms, Unconventional Intelligent Drilling and Intelligent Equipment for Continuous Operation in Ultra-Deep Wells, PetroChina–China University of Petroleum (Beijing) Strategic Cooperation Project.
Abstract (Originalsprache)
Horizontal well drilling is the mainstream technology for developing deep oil and gas resources. Engineering practice has demonstrated that hydraulic oscillators can solve the problem of the backing pressure of pipe strings and improve drilling efficiency. However, the design of excitation parameters for hydraulic oscillators is currently largely based on idealized friction models and does not fully consider the nonlinear characteristics of friction between the drill string and the formation, resulting in a lack of quantitative basis for parameter selection under different operating conditions. A series of laboratory friction tests was conducted to systematically characterize the dependence of interfacial friction behavior on sliding velocity across different combinations of drill string materials, drilling fluid systems, and rock lithologies. Based on the experimentally determined velocity–friction relationships, a drill string dynamic model incorporating a hydraulic oscillator was developed in which nonlinear frictional effects at the interface were explicitly represented. Using this modeling framework, parametric simulations were carried out to examine how variations in excitation amplitude and excitation frequency influence drag reduction performance under diverse operating conditions. The simulation results indicate that the contribution of drill string material to overall drag reduction effectiveness is comparatively limited, whereas drilling fluid type plays a dominant regulatory role. Oil-based drilling fluids significantly enhance drag reduction performance relative to water-based systems and exhibit greater responsiveness to adjustments in excitation parameters. Rock lithology exerts a pronounced influence on the effectiveness of drag reduction. When water-based drilling fluids are used, the overall performance ranks from highest to lowest as limestone, shale, and sandstone. In contrast, under oil-based drilling fluid conditions, the relative ordering shifts to shale, followed by sandstone, and then limestone. Excitation amplitude is the dominant parameter in enhancing drag reduction capability, and in most cases, its incremental effect exceeds that of excitation frequency; however, under certain specific operating conditions, increasing the excitation frequency can provide additional drag reduction benefits. Based on the above findings, a hydraulic oscillator excitation parameter design method was proposed that matches drilling conditions and formation characteristics by distinguishing between different drilling fluid environments and lithologies, with amplitude as the primary control parameter and frequency as a supplementary parameter. This method provides a theoretical foundation for the design of output parameters of hydraulic oscillators operating under diverse working conditions.
Förderung
- Intelligent Magnetic Guidance and Dynamic Risk Prevention for Large Platforms
- Unconventional Intelligent Drilling and Intelligent Equipment for Continuous Operation in Ultra-Deep Wells
- PetroChina–China University of Petroleum (Beijing) Strategic Cooperation Project
Zitieren
APA
He, X., Liu, G., Chen, T., Li, J., Wang, W., Li, S., & Wang, L. (2026). A Design Method for Hydraulic Oscillator Excitation Parameters Considering Drilling Conditions and Formation Characteristics. Applied Sciences, 16(6), 2705. https://doi.org/10.3390/app16062705
Vancouver
He X, Liu G, Chen T, Li J, Wang W, Li S, et al. A Design Method for Hydraulic Oscillator Excitation Parameters Considering Drilling Conditions and Formation Characteristics. Applied Sciences. 2026;16(6):2705. doi:10.3390/app16062705
BibTeX
@article{He2026,
author = {He, Xin and Liu, Gonghui and Chen, Tian and Li, Jun and Wang, Wei and Li, Shichang and Wang, Lincong},
title = {A Design Method for Hydraulic Oscillator Excitation Parameters Considering Drilling Conditions and Formation Characteristics},
journal = {Applied Sciences},
year = {2026},
volume = {16},
number = {6},
pages = {2705},
doi = {10.3390/app16062705}
}
EUVIMED