EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Use of Computer Vision Methodologies to Estimate the Volume of Powdered Substance Shapes

Jovan Šulc, Vule Reljić, Vladimir Jurošević, Lidija Krstanović, Bojan Banjac, Željko Santoši

Applied Sciences · 19.02.2026 · 16 (4) · 2053

DOI: 10.3390/app16042053 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Sciences, online erschienen am 19.02.2026. Verfasst von Jovan Šulc und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Fund of the Republic of Serbia, Ministry of Science, Technological Development and Innovation of the Republic of Serbia.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Many compressed air devices are energy inefficient. One example is using air nozzles above pastry lines to remove flour and cool products. These nozzles consume excessive energy, particularly when mounted too high, requiring stronger airflow. Adjustable nozzle height and energy-efficient nozzles should be used with careful control of air pressure, flow rate, and activation time, ensuring efficient and adaptive control. Additionally, sensor-based control should activate airflow only when pastries are present and until the correct amount of powder material has been blown out, as the nozzles often operate unnecessarily. Accurate measurement of powder volume after blow-off remains a challenge. With the use of computer vision methodology, the system would continuously read the measured values and determine not only the optimal moment to interrupt device operation but also dynamically adjust key parameters. This paper demonstrates that computer vision can estimate powder volume using two non-contact 3D methods: a depth camera, and a structured light scanner. Their accuracy, reliability, advantages, and limitations are analyzed. The results show that the structured light scanner can be used in the case of a static model (the conveyor belt with products stops at the moment when it is necessary to perform a 3D measurement). This approach shows higher repeatability and gives a more accurate 3D model. On the other hand, for the dynamic model (the conveyor belt with products moves while the 3D measurement device is fixed), the depth camera can be used because, at minimum rotation speeds of the substrate, it shows higher accuracy and enables faster adaptive modeling and creation of the necessary data.

Förderung

  • Science Fund of the Republic of Serbia
  • Ministry of Science, Technological Development and Innovation of the Republic of Serbia

Zitieren

APA

Šulc, J., Reljić, V., Jurošević, V., Krstanović, L., Banjac, B., & Santoši, Ž. (2026). The Use of Computer Vision Methodologies to Estimate the Volume of Powdered Substance Shapes. Applied Sciences, 16(4), 2053. https://doi.org/10.3390/app16042053

Vancouver

Šulc J, Reljić V, Jurošević V, Krstanović L, Banjac B, Santoši Ž. The Use of Computer Vision Methodologies to Estimate the Volume of Powdered Substance Shapes. Applied Sciences. 2026;16(4):2053. doi:10.3390/app16042053

BibTeX
@article{ulc2026,
  author = {Šulc, Jovan and Reljić, Vule and Jurošević, Vladimir and Krstanović, Lidija and Banjac, Bojan and Santoši, Željko},
  title = {The Use of Computer Vision Methodologies to Estimate the Volume of Powdered Substance Shapes},
  journal = {Applied Sciences},
  year = {2026},
  volume = {16},
  number = {4},
  pages = {2053},
  doi = {10.3390/app16042053}
}
Kostenlos starten →