EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Flow Field Simulation of a Hydrogeological Exploration Drill Bit for Switching between Coring Drilling and Non-Coring Drilling

Yuanling Shi, Conghui Li

Applied Sciences · 05.06.2024 · 14 (11) · 4893

DOI: 10.3390/app14114893 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Applied Sciences, online erschienen am 05.06.2024. Verfasst von Yuanling Shi und 1 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Anhui Provincial Natural Science Foundation, Natural Science Research Project of Anhui Educational Committe, Academician Workstation in Anhui Province, Anhui University of Science and Technology.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Drilling is one of the most commonly used techniques in hydrogeological exploration and is employed to obtain rock samples and create boreholes. During conventional drilling, it is necessary to raise all the drilling tools in the borehole when switching between coring drilling and non-coring drilling, which causes large auxiliary operation time consumption and poor drilling efficiency. Based on the structure of wireline coring tools, a large diameter modular drill bit was designed to switch between coring drilling and non-coring drilling without lifting the whole set of drilling tools. In the COMSOL simulation environment, a simulation model of the modular bit was constructed. Drilling fluid velocity and pressure characteristics flowing through the modular bit were studied. According to the analysis results, with the same input flow rate, similar velocities and lower pressure loss can be obtained in non-coring drilling as with the coring bit, and thus drilling cuttings can be removed effectively even if there are more cuttings produced in non-coring drilling than in coring drilling for a borehole drilled at the same diameter. When the outside diameter of the modular bit is 216 mm, the recommended clearance value is 9 mm or 10 mm in order to obtain lower pressure loss and larger diameter core. To generate low pressure loss and ensure bit strength, a layout with four nozzles on the internal non-coring bit is recommended. The modular bit enables fast switching between coring drilling and non-coring drilling without raising the drilling tools. The simulation model can be used for drilling parameter selection and drill bit optimization.

Förderung

  • Anhui Provincial Natural Science Foundation
  • Natural Science Research Project of Anhui Educational Committe
  • Academician Workstation in Anhui Province, Anhui University of Science and Technology
  • Anhui Provincial Major Science and Technology Project
  • Scientific Research Foundation for High-Level Talents of Anhui University of Science and Technology

Zitieren

APA

Shi, Y., & Li, C. (2024). Flow Field Simulation of a Hydrogeological Exploration Drill Bit for Switching between Coring Drilling and Non-Coring Drilling. Applied Sciences, 14(11), 4893. https://doi.org/10.3390/app14114893

Vancouver

Shi Y, Li C. Flow Field Simulation of a Hydrogeological Exploration Drill Bit for Switching between Coring Drilling and Non-Coring Drilling. Applied Sciences. 2024;14(11):4893. doi:10.3390/app14114893

BibTeX
@article{Shi2024,
  author = {Shi, Yuanling and Li, Conghui},
  title = {Flow Field Simulation of a Hydrogeological Exploration Drill Bit for Switching between Coring Drilling and Non-Coring Drilling},
  journal = {Applied Sciences},
  year = {2024},
  volume = {14},
  number = {11},
  pages = {4893},
  doi = {10.3390/app14114893}
}
Kostenlos starten →