EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Feasibility on equivalence ratio measurement via OH*, CH*, and C2* chemiluminescence and study of soot emissions in co-flow non-premixed DME/C1–C2 hydrocarbon flames

Abdallah Abu Saleh, Kevin J. Hughes, Graham Hargrave, Ruoyang Yuan

Frontiers in Fuels · 2024

DOI: 10.3389/ffuel.2023.1296502 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Fuels, 2024. Verfasst von Abdallah Abu Saleh und 3 weiteren Autor:innen. Die Arbeit nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The effects of dimethyl ether (DME) addition to methane and ethylene fuels on the combustion characteristics of heat release, soot emissions, and flame temperature were investigated experimentally and numerically in a non-premixed laminar flame configuration. The flame-heat release soot-volume fraction was measured experimentally using CH*, OH*, and C 2 * chemiluminescence and planar two-color soot pyrometry, respectively. The CH*, OH*, and C 2 * were used to locate flame-heat release regions as well as to investigate the soot signal’s effect on their measurements. The ratios of the chemiluminescence pairs (OH*/CH* and OH*/C 2 *) were studied for the feasibility of map local equivalence ratios. Numerical calculations across a full range of DME mixing ratios were performed through 1D laminar flame simulations implemented with a detailed mechanism to provide an indication of the flame structures and profiles of key species including OH*, OH, CH*, CH, CH 3 , C 3 H 3 , C 2 H 2 , heat release rate (HRR), and flame temperature. An existing developed soot model was used in a 2D computational study to investigate its validity for modeling soot for DME (oxygenated fuel)/C 2 H 4 /N 2 flames. Parametric studies have been carried out on some key parameters in the soot model to find optimum values that can be used in future studies. Although soot radiation intensities increased at a small amount (25%vol) of DME addition in the DME/methane flames, the soot pyrometry results showed a reduced soot volume fraction with an increased DME mixture ratio in both DME/methane and DME/ethylene flames studied, agreeing with the key conclusion of 1D numerical results. The flame HRR decreases with the increasing addition of DME to methane and ethylene flames and correlates with the trend of OH* and CH* profiles. The 1D simulation showed a non-monotonic correlation between OH*/CH* ratios and equivalence ratios, implying a limited use of OH*/CH* for the equivalence ratio measurement in non-premixed flames with DME additions.

Zitieren

APA

Saleh, A. A., Hughes, K. J., Hargrave, G., & Yuan, R. (2024). Feasibility on equivalence ratio measurement via OH*, CH*, and C2* chemiluminescence and study of soot emissions in co-flow non-premixed DME/C1–C2 hydrocarbon flames. Frontiers in Fuels. https://doi.org/10.3389/ffuel.2023.1296502

Vancouver

Saleh AA, Hughes KJ, Hargrave G, Yuan R. Feasibility on equivalence ratio measurement via OH*, CH*, and C2* chemiluminescence and study of soot emissions in co-flow non-premixed DME/C1–C2 hydrocarbon flames. Frontiers in Fuels. 2024. doi:10.3389/ffuel.2023.1296502

BibTeX
@article{Saleh2024,
  author = {Saleh, Abdallah Abu and Hughes, Kevin J. and Hargrave, Graham and Yuan, Ruoyang},
  title = {Feasibility on equivalence ratio measurement via OH*, CH*, and C2* chemiluminescence and study of soot emissions in co-flow non-premixed DME/C1–C2 hydrocarbon flames},
  journal = {Frontiers in Fuels},
  year = {2024},
  doi = {10.3389/ffuel.2023.1296502}
}
Kostenlos starten →