EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Biofunctional hydrogel adsorbents for sustainable downstream dye purification and circular wastewater management

Subhasis Patra, Anurag Panda, Prasenjit Chakraborty, Aradhana Basu, Arunava Sengupta, Gausal Azam Khan, Jayato Nayak, Sankha Chakrabortty, Shirsendu Banerjee, Suraj K. Tripathy

Frontiers in Chemical Engineering · 17.07.2026 · 8

DOI: 10.3389/fceng.2026.1895352 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Frontiers in Chemical Engineering, online erschienen am 17.07.2026. Verfasst von Subhasis Patra und 9 weiteren Autor:innen. Die Arbeit nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Scientific Research, King Faisal University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Although the use of clay–alginate composites and activated clays as adsorbents has been thoroughly examined for the removal of dyes, very few studies have addressed the effect of reactor hydrodynamics on the efficiency of the process. In this research, efforts were made to fill the knowledge gaps by adopting an approach combining batch adsorption tests, fixed-bed column studies, breakthrough modeling, and computational fluid dynamics (CFD) simulation in order to create connections between flow characteristics and mass transfer and adsorption kinetics involved in the removal of malachite green (MG) dye using mesoporous AC@SA hydrogel beads.

Methods

Mesoporous hydrogel beads possessed pore sizes in the range of 3–10 nm and exhibited a negative zeta potential of –8 mV (mean). Batch adsorption tests, fixedbed column studies, breakthrough modeling, and CFD simulations were conducted to evaluate adsorption performance and investigate the influence of reactor hydrodynamics on the adsorption process.

Results

Maximum MG dye removal efficiency was observed to be around 90% in batch adsorption tests at 50 g L −1 adsorbent dose, pH 7, and 150 rpm after about 120–150 min contact time. Column experiments showed an increase in bed height from 6 to 14 cm increased the breakthrough time from about 18 to 32 min, while increasing the influent dye concentration and flow rate reduced breakthrough times. The Thomas model showed excellent agreement with experimental data (R 2 ≈ 0.99), with adsorption capacities reaching 21.28 mg g −1 and rate constants ranging from 0.22 to 0.33 ml mg −1 min −1 . Further simulations by CFD revealed that a flow rate of 10 ml min −1 would ensure uniformity of velocity, lower turbulence, controlled eddy viscosity, and stable hydrodynamic conditions, hence maximized adsorption.

Discussion

Such an approach ensures not only knowledge from the material level but also at the reactor level concerning adsorption process optimization and scaling up. Additionally, the system has ensured achievement of SDGs 6, 9, and 12 due to the use of environmentally friendly materials and wastewater treatment approaches.

Förderung

  • Deanship of Scientific Research, King Faisal University

Zitieren

APA

Patra, S., Panda, A., Chakraborty, P., Basu, A., Sengupta, A., Khan, G. A., Nayak, J., Chakrabortty, S., Banerjee, S., & Tripathy, S. K. (2026). Biofunctional hydrogel adsorbents for sustainable downstream dye purification and circular wastewater management. Frontiers in Chemical Engineering, 8. https://doi.org/10.3389/fceng.2026.1895352

Vancouver

Patra S, Panda A, Chakraborty P, Basu A, Sengupta A, Khan GA, et al. Biofunctional hydrogel adsorbents for sustainable downstream dye purification and circular wastewater management. Frontiers in Chemical Engineering. 2026;8. doi:10.3389/fceng.2026.1895352

BibTeX
@article{Patra2026,
  author = {Patra, Subhasis and Panda, Anurag and Chakraborty, Prasenjit and Basu, Aradhana and Sengupta, Arunava and Khan, Gausal Azam and Nayak, Jayato and Chakrabortty, Sankha and Banerjee, Shirsendu and Tripathy, Suraj K.},
  title = {Biofunctional hydrogel adsorbents for sustainable downstream dye purification and circular wastewater management},
  journal = {Frontiers in Chemical Engineering},
  year = {2026},
  volume = {8},
  doi = {10.3389/fceng.2026.1895352}
}
Kostenlos starten →