EUVIMEDEUVIMED entdecken
Crossref

Black liquor spray properties in-furnace conditions for swirl cone nozzles TAPPI Journal July 2026

Ari Kankkunen, Ari Ainsalo, Andy Jones, James Biggs, Jukka Röppänen, Mika Järvinen

TAPPI Journal · 31.07.2026 · 25 (7) · 430

DOI: 10.32964/tj25.7.430 ↗

Kurz gefasst

Fachartikel in der Zeitschrift TAPPI Journal, online erschienen am 31.07.2026. Verfasst von Ari Kankkunen und 5 weiteren Autor:innen. Die Arbeit nennt 18 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ÄTe), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™] Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.

Zitieren

APA

Kankkunen, A., Ainsalo, A., Jones, A., Biggs, J., Röppänen, J., & Järvinen, M. (2026). Black liquor spray properties in-furnace conditions for swirl cone nozzles TAPPI Journal July 2026. TAPPI Journal, 25(7), 430. https://doi.org/10.32964/tj25.7.430

Vancouver

Kankkunen A, Ainsalo A, Jones A, Biggs J, Röppänen J, Järvinen M. Black liquor spray properties in-furnace conditions for swirl cone nozzles TAPPI Journal July 2026. TAPPI Journal. 2026;25(7):430. doi:10.32964/tj25.7.430

BibTeX
@article{Kankkunen2026,
  author = {Kankkunen, Ari and Ainsalo, Ari and Jones, Andy and Biggs, James and Röppänen, Jukka and Järvinen, Mika},
  title = {Black liquor spray properties in-furnace conditions for swirl cone nozzles TAPPI Journal July 2026},
  journal = {TAPPI Journal},
  year = {2026},
  volume = {25},
  number = {7},
  pages = {430},
  doi = {10.32964/tj25.7.430}
}
Kostenlos starten →