EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-SA 4.0

Impact of Endurance Testing on the Thermal Performance of a Retrofitted FDM 3D Printer

Alexander Ariantono Nugroho, David Christanto, Laurentius Yudha Bramantyo, Bondan Wiratmoko Budi Santoso, Ign. R. Haryosuprobo, Mardiatno

Jurnal Rekayasa Mesin · 30.04.2026 · 21 (1) · 129-138

DOI: 10.32497/jrm.v21i1.7025 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Jurnal Rekayasa Mesin, online erschienen am 30.04.2026. Verfasst von Alexander Ariantono Nugroho und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-SA 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The reliability of retrofitted Fused Deposition Modeling (FDM) 3D printers is affected by thermal stability during long print cycles. This study evaluated the thermal performance of a retrofitted BFB 3D Touch Cartesian FDM printer equipped with dual extruders, automatic bed leveling, a BTT SKR v1.4 controller, and a 24 V/360 W power supply unit (PSU). An 80 × 80 × 80 mm calibration cube was printed for 5 h to impose a continuous thermal load. Surface temperatures of stepper drivers, stepper motors, mainboard, PSU, and heated bed were measured with a TR-10 thermal imager at 1 h intervals, while bed preheating was recorded for 7 min at P1-P4 and the bed center. The Y1 driver reached 68.7 °C at hour 3, the PSU reached 65.0 °C at hour 5, and the extruder motor reached 52.7 °C. The bed center reached 59.2 °C at minute 7, but the corner regions were lower and locally non-monotonic. These fluctuations are interpreted as effects of local heat-transfer non-uniformity and measurement instability rather than uniform bed cooling. This study shows that driver and PSU cooling, cable-size verification, repeated measurements, and bed insulation are required to improve retrofit-printer reliability in extended operation.

Zitieren

APA

Nugroho, A. A., Christanto, D., Bramantyo, L. Y., Santoso, B. W. B., Haryosuprobo, I. R., & Mardiatno (2026). Impact of Endurance Testing on the Thermal Performance of a Retrofitted FDM 3D Printer. Jurnal Rekayasa Mesin, 21(1), 129-138. https://doi.org/10.32497/jrm.v21i1.7025

Vancouver

Nugroho AA, Christanto D, Bramantyo LY, Santoso BWB, Haryosuprobo IR, Mardiatno. Impact of Endurance Testing on the Thermal Performance of a Retrofitted FDM 3D Printer. Jurnal Rekayasa Mesin. 2026;21(1):129-138. doi:10.32497/jrm.v21i1.7025

BibTeX
@article{Nugroho2026,
  author = {Nugroho, Alexander Ariantono and Christanto, David and Bramantyo, Laurentius Yudha and Santoso, Bondan Wiratmoko Budi and Haryosuprobo, Ign. R. and Mardiatno},
  title = {Impact of Endurance Testing on the Thermal Performance of a Retrofitted FDM 3D Printer},
  journal = {Jurnal Rekayasa Mesin},
  year = {2026},
  volume = {21},
  number = {1},
  pages = {129--138},
  doi = {10.32497/jrm.v21i1.7025}
}
Kostenlos starten →