Beyond a Single Damping Coefficient: Experimental Mapping of Nonlinear and Stroke-Dependent Automotive Shock-Absorber Behaviour
Journal of Mechanical Engineering and Applied Technology · 25.07.2026 · 4 (2) · 123-136
DOI: 10.32497/jmeat.v4i2.7842 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Mechanical Engineering and Applied Technology, online erschienen am 25.07.2026. Verfasst von Avicenna An-Nizhami und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-SA 4.0).
Themen: Schlaganfall
Abstract (Originalsprache)
Shock absorbers are commonly represented by a constant viscous damping coefficient, although their actual force response may vary nonlinearly with piston velocity, stroke amplitude, and operating conditions. This study experimentally compared the damping characteristics of original and aftermarket rear shock absorbers using a laboratory test rig with variable-speed and variable-stroke operation. Both specimens were tested at strokes of 60, 90, and 120 mm and excitation frequencies of 0.5–2.0 Hz, corresponding to peak piston velocities of 0.0942–0.7539 m/s. Maximum damping forces were measured using a force gauge, and the resulting force–velocity relationships were evaluated before and after modification of the test rig. Three-term sinusoidal functions were also fitted to the measured data using the MATLAB Curve Fitting Tool. Both shock absorbers exhibited nonlinear digressive behaviour, characterised by a rapid force increase at low-to-intermediate velocities followed by a stroke-dependent high-speed plateau. Matched-velocity comparisons showed that damping force varied with stroke even at approximately equal peak velocities, demonstrating that the response was not governed by piston velocity alone. Using the post-modification data, the aftermarket shock absorber generated an average damping force 15.8% higher than the original unit over the complete test matrix. Its peak force exceeded that of the original shock absorber by 29.4%, 9.8%, and 12.6% at strokes of 60, 90, and 120 mm, respectively. The corresponding apparent damping coefficients were also consistently higher for the aftermarket unit. These findings demonstrate that shock-absorber performance should be evaluated using experimentally determined force–velocity operating maps across multiple strokes and velocities rather than a single nominal damping coefficient.
Zitieren
APA
An-Nizhami, A., Widodo, I. G., Ulum, M. S. N., Riadini, E. R., Mamba’udin, A., & Wirawan, Y. B. (2026). Beyond a Single Damping Coefficient: Experimental Mapping of Nonlinear and Stroke-Dependent Automotive Shock-Absorber Behaviour. Journal of Mechanical Engineering and Applied Technology, 4(2), 123-136. https://doi.org/10.32497/jmeat.v4i2.7842
Vancouver
An-Nizhami A, Widodo IG, Ulum MSN, Riadini ER, Mamba’udin A, Wirawan YB. Beyond a Single Damping Coefficient: Experimental Mapping of Nonlinear and Stroke-Dependent Automotive Shock-Absorber Behaviour. Journal of Mechanical Engineering and Applied Technology. 2026;4(2):123-136. doi:10.32497/jmeat.v4i2.7842
BibTeX
@article{AnNizhami2026,
author = {An-Nizhami, Avicenna and Widodo, Ignatius Gunawan and Ulum, Muhammad Showi Nailul and Riadini, Elfrida Rizky and Mamba’udin, Ahmad and Wirawan, Yuris Bahadur},
title = {Beyond a Single Damping Coefficient: Experimental Mapping of Nonlinear and Stroke-Dependent Automotive Shock-Absorber Behaviour},
journal = {Journal of Mechanical Engineering and Applied Technology},
year = {2026},
volume = {4},
number = {2},
pages = {123--136},
doi = {10.32497/jmeat.v4i2.7842}
}
EUVIMED