EUVIMEDEUVIMED entdecken
Fallbericht

Custom-made 3D-printed porous metal acetabular composite component in revision hip arthroplasty with Paprosky type III acetabular defects: A case report

Cong Xiao, Shaoyun Zhang, Zhixiang Gao, Chongqi Tu

Technology and Health Care · 2023

DOI: 10.3233/thc-212984 ↗

Kurz gefasst

Fallbericht in der Zeitschrift Technology and Health Care, 2023. Verfasst von Cong Xiao und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopedics, The Third Hospital of Mianyang, Sichuan Mental Health Center, Mianyang, Sichuan, China. Hauptthemen laut MEDLINE: Arthroplasty, Replacement, Hip, Hip Prosthesis. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 20 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND: Increases in the numbers of surgical procedures for primary total hip arthroplasty (THA) inevitably lead to increases in the requirements for revision THA. The achievement of long-term stability is difficult or impossible by conventional implants in patients with severe destruction of the acetabulum. OBJECTIVE: This case report presents a successful treatment using a specific three-dimensional (3D)-printed porous titanium acetabular composite component without a flange in the management of Paprosky type IIIB acetabular defects. METHOD: A 65-year-old female diagnosed with right hip prosthetic loosening with a huge acetabular defect presented to our hospital. We designed the 3D model of the pelvis and created an individualized 3D-printed porous titanium acetabular composite component for revision THA. The procedure was performed through a posterolateral approach, and the component was implanted in the defect and fixed with cup screws using the drill guides. RESULTS: At the last follow-up at 2 years, the patient had a satisfactory hip joint function and no signs of loosening or other complications were found. CONCLUSIONS: The 3D-printed porous titanium acetabular composite component without a flange is showing promising clinical and radiological outcomes in the management of Paprosky type III acetabular defects.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Arthroplasty, Replacement, HipHip ProsthesisFemaleHumansAgedAcetabulumTitaniumPorosityMetalsReoperationPrinting, Three-DimensionalRetrospective StudiesProsthesis FailureFollow-Up Studies

Stichwörter der Autor:innen

3D printingRevision hip arthroplastyacetabular defectscase reportcomposite componentcustom-madeporous titanium

Substanzen

TitaniumMetals

Autor:innen und Institutionen

  • Department of Orthopedics, The Third Hospital of Mianyang, Sichuan Mental Health Center, Mianyang, Sichuan, China.
  • Department of Orthopedics, West China Hospital, Sichuan University, Chengdu, Sichuan, China.

Zitieren

APA

Xiao, C., Zhang, S., Gao, Z., & Tu, C. (2023). Custom-made 3D-printed porous metal acetabular composite component in revision hip arthroplasty with Paprosky type III acetabular defects: A case report. Technology and Health Care. https://doi.org/10.3233/thc-212984

Vancouver

Xiao C, Zhang S, Gao Z, Tu C. Custom-made 3D-printed porous metal acetabular composite component in revision hip arthroplasty with Paprosky type III acetabular defects: A case report. Technology and Health Care. 2023. doi:10.3233/thc-212984

BibTeX
@article{Xiao2023,
  author = {Xiao, Cong and Zhang, Shaoyun and Gao, Zhixiang and Tu, Chongqi},
  title = {Custom-made 3D-printed porous metal acetabular composite component in revision hip arthroplasty with Paprosky type III acetabular defects: A case report},
  journal = {Technology and Health Care},
  year = {2023},
  doi = {10.3233/thc-212984}
}
Kostenlos starten →