EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure, mechanical, wear, fracture behavior, and machining characteristics of stir-cast A356/n-TiC composites: influence of reinforcement fraction and quenching media

Kiran Kumar K U, Bharathi V, Ningegowda B M, D Balasubramaniam, K C Nagaraja

Fracture and Structural Integrity · 22.11.2026 · 21 (79) · 266-285

DOI: 10.3221/igf-esis.79.15 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Fracture and Structural Integrity, online erschienen am 22.11.2026. Verfasst von Kiran Kumar K U und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Stir casting was used to reinforce aluminum alloy, A356, with varying wt. % of titanium carbide (TiC) nanoparticles (0%, 1%, 2%, 3%, and 4%). Solution treatment at 520°C for two hours, quenching in three distinct agents (brine solution, synthetic oil, and hot water), and subsequent aging at 180°C for four hours was carried out. The objective was to examine how microstructure, mechanical, and machining characteristics of the stir-cast n-TiC reinforced A356 composites were affected by n-TiC reinforcement and quenching agents. It was observed that nanoparticles were uniformly distributed throughout the matrix, on the basis of microstructural studies. Among the compositions tested (0 to 4 %), 3 % n-TiC reinforcement exhibited the best mechanical performance, reaching high increase in hardness, tensile strength, and wear resistance. With a 36.2% increase in hardness, a 16.4% increase in tensile strength, and a 39.5% decrease in wear loss, brine quenching produced the greatest overall improvement of all compositions. The ANOVA findings showed that the following factors influenced the machining force, Fm (N), and surface roughness (Ra): wt. % of n-TiC, cooling/quenching agent, depth of cut (mm/min), and cutting speed (rpm). The confirmatory test results confirmed the model's validity within acceptable limits. Specifically, the errors in machining force and surface roughness (Ra) were 9.81% and 7.69%, respectively.

Zitieren

APA

U, K. K. K., V, B., M, N. B., Balasubramaniam, D., & Nagaraja, K. C. (2026). Microstructure, mechanical, wear, fracture behavior, and machining characteristics of stir-cast A356/n-TiC composites: influence of reinforcement fraction and quenching media. Fracture and Structural Integrity, 21(79), 266-285. https://doi.org/10.3221/igf-esis.79.15

Vancouver

U KKK, V B, M NB, Balasubramaniam D, Nagaraja KC. Microstructure, mechanical, wear, fracture behavior, and machining characteristics of stir-cast A356/n-TiC composites: influence of reinforcement fraction and quenching media. Fracture and Structural Integrity. 2026;21(79):266-285. doi:10.3221/igf-esis.79.15

BibTeX
@article{U2026,
  author = {U, Kiran Kumar K and V, Bharathi and M, Ningegowda B and Balasubramaniam, D and Nagaraja, K C},
  title = {Microstructure, mechanical, wear, fracture behavior, and machining characteristics of stir-cast A356/n-TiC composites: influence of reinforcement fraction and quenching media},
  journal = {Fracture and Structural Integrity},
  year = {2026},
  volume = {21},
  number = {79},
  pages = {266--285},
  doi = {10.3221/igf-esis.79.15}
}
Kostenlos starten →