EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Entwurf eines einfachen Messaufbaus zur Bestimmung der Durchlaufzeit von Hörgeräten

Angermeier, J., Würz, N., Roth, S., Zirn, S.

GMS Zeitschrift für Audiologie – Audiological Acoustics · 23.11.2020 · 1-1

DOI: 10.3205/zaud000011 ↗

Kurz gefasst

Fachartikel in der Zeitschrift GMS Zeitschrift für Audiologie – Audiological Acoustics, erschienen am 23.11.2020. Verfasst von Angermeier und 7 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref). Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In bimodal cochlear implant/hearing aid users, differences in signal processing may result in a time-delayed stimulation of the two modalities. Recent studies have shown that sound localization can improve when the device delay mismatch is reduced. To perform such an adjustment, the hearing aid processing delay must be determined by measurement. Commercially available hearing aid test boxes can often provide these values. However, the signal processing used is often not fully revealed. In this work an alternative and understandable approach how to design a simple measuring unit based on an Arduino DUE microcontroller board is presented. For this purpose, a measuring table was 3D printed. On this table a hearing aid can be connected to a microphone using a 2 ccm coupler. By performing a latency comparison with the signal measured simultaneously by a reference microphone, the processing latency of hearing aids can be determined. This comparison is performed frequency-dependently applying cross-correlation between target signal and reference signal. Recording, presentation and storing of the used signals is done by an ATMEL SAM3X8E microcontroller which is built onto an Arduino DUE. Via additional electronic circuits the used microphones and speaker are connected to the microcontroller. After completion of a measurement (measuring duration approx. 5 s) the data processing is done on a PC in MATLAB. Preliminary results show a high stability of the methodology for different sound pressure levels with standard deviations between 30 µs and 60 µs in a level range between 50 and 75 dB (A). The presented setup is currently used for determination of hearing aid processing delays in ongoing studies.

Schlagwörter

hearing aidscochlear implantsprocessing delaysmicrocontrollerHörgeräteCochlea-ImplantateDurchlaufzeitenMikrocontroller

Zitieren

APA

Angermeier, J., Würz, N., Roth, S., Zirn, & S. (2020). Entwurf eines einfachen Messaufbaus zur Bestimmung der Durchlaufzeit von Hörgeräten. GMS Zeitschrift für Audiologie – Audiological Acoustics, 1-1. https://doi.org/10.3205/zaud000011

Vancouver

Angermeier, J., Würz, N., Roth, S., et al. Entwurf eines einfachen Messaufbaus zur Bestimmung der Durchlaufzeit von Hörgeräten. GMS Zeitschrift für Audiologie – Audiological Acoustics. 2020:1-1. doi:10.3205/zaud000011

BibTeX
@article{Angermeier2020,
  author = {Angermeier and J. and Würz and N. and Roth and S. and Zirn and S.},
  title = {Entwurf eines einfachen Messaufbaus zur Bestimmung der Durchlaufzeit von Hörgeräten},
  journal = {GMS Zeitschrift für Audiologie – Audiological Acoustics},
  year = {2020},
  pages = {1--1},
  doi = {10.3205/zaud000011}
}
Kostenlos starten →