EUVIMEDEUVIMED entdecken
Crossref

The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets

İmren Ozturk Yılmaz

Düzce Üniversitesi Bilim ve Teknoloji Dergisi · 19.04.2026 · 14 (2) · 340-351

DOI: 10.29130/dubited.1760460 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Düzce Üniversitesi Bilim ve Teknoloji Dergisi, online erschienen am 19.04.2026. Verfasst von İmren Ozturk Yılmaz. Die Arbeit nennt 38 Literaturangaben. Gefördert von: This research received no external funding..

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the resistance spot welding behavior of dissimilar low-carbon CR3 steel and coated transformation-induced plasticity-aided bainitic ferrite (TBF) steel sheets widely used in automotive body applications. The effects of welding current (6-7-8-9 kA) and welding time (240–400 ms) on weld microstructure, nugget size, indentation depth, and mechanical performance were systematically examined. Metallographic analysis revealed no macroscopic weld defects; however, limited mixing was observed in the fusion zone, particularly at lower heat inputs. Increasing heat input enhanced material mixing and widened the heat-affected zone (HAZ), especially on the TBF side, but also promoted liquid metal embrittlement (LME)-induced surface microcracks associated with Zn-coating penetration along grain boundaries. The maximum nugget size reached 8.34 mm at 9 kA–400 ms, while the indentation depth remained within automotive acceptance limits, with a maximum value of 21.65%. Tensile-shear tests showed that all fractures occurred in the HAZ of the thinner CR3 sheet in a tearing mode, with a maximum failure load of 4.25 kN at 7 kA–240 ms. Despite the presence of microcracks in the TBF HAZ, the joint strength was governed by the lower-strength CR3 sheet. The results highlight the importance of optimized welding parameters to balance sufficient nugget growth and minimize LME susceptibility in dissimilar advanced high-strength steel (AHSS)–mild steel combinations.

Förderung

  • This research received no external funding.

Zitieren

APA

Yılmaz, İ. O. (2026). The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets. Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 14(2), 340-351. https://doi.org/10.29130/dubited.1760460

Vancouver

Yılmaz İO. The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets. Düzce Üniversitesi Bilim ve Teknoloji Dergisi. 2026;14(2):340-351. doi:10.29130/dubited.1760460

BibTeX
@article{Ylmaz2026,
  author = {Yılmaz, İmren Ozturk},
  title = {The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets},
  journal = {Düzce Üniversitesi Bilim ve Teknoloji Dergisi},
  year = {2026},
  volume = {14},
  number = {2},
  pages = {340--351},
  doi = {10.29130/dubited.1760460}
}
Kostenlos starten →