Experimental and Numerical Investigation of Dissimilar AISI 1045/S235JR Steels Welded by Automated GMAW
Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji · 10.11.2026 · (Advanced Online Publication)
DOI: 10.29109/gujsc.2034682 ↗Kurz gefasst
Fachartikel in der Zeitschrift Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, online erschienen am 10.11.2026. Verfasst von Kaan Kuştepe und 2 weiteren Autor:innen. Die Arbeit nennt 63 Literaturangaben.
Abstract (Originalsprache)
Gas metal arc welding (GMAW) is widely employed in structural steel applications due to its high deposition efficiency, process flexibility, and suitability for automation. However, joining dissimilar steels remains challenging because differences in chemical composition, mechanical properties, and thermal response can significantly affect joint performance. This study presents an experimental and numerical investigation of the effects of welding current (80, 90, and 100 A) and welding speed (400, 500, and 600 mm/min) on dissimilar AISI 1045/S235JR GMAW joints. Welding was performed using an automated adjustable platform to minimize operator-induced variability and improve process repeatability. Joint performance was evaluated through tensile testing, Rockwell B hardness measurements, and weld cross-section geometry measurements, while finite element analysis (FEA) in ANSYS was used to investigate temperature distribution, stress development, and deformation behavior. The results showed that increasing welding current generally increased weld bead width, bead height, and heat-affected zone (HAZ) width, whereas increasing welding speed reduced these dimensions due to the corresponding decrease in heat input per unit length. Hardness measurements revealed more pronounced variations in the HAZ on the AISI 1045 side, while the S235JR side exhibited a comparatively moderate hardness response and the weld metal maintained relatively stable hardness values. Tensile results indicated a general reduction in joint performance with increasing welding speed, accompanied by a greater tendency for weld-zone fracture under selected high-speed conditions. Among the investigated parameters, 80 A–400 mm/min produced the highest tensile strength and favorable fracture behavior, with failure occurring outside the weld zone. The numerical results exhibited trends consistent with the experimental findings and similarly identified 80 A–400 mm/min as the most favorable condition. Overall, the results demonstrate that the combined control of welding current, welding speed, and heat input is critical for achieving reliable mechanical performance in dissimilar AISI 1045/S235JR welded joints.
Zitieren
APA
Kuştepe, K., Kursun, B. D., & Güler, E. S. (2026). Experimental and Numerical Investigation of Dissimilar AISI 1045/S235JR Steels Welded by Automated GMAW. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji. https://doi.org/10.29109/gujsc.2034682
Vancouver
Kuştepe K, Kursun BD, Güler ES. Experimental and Numerical Investigation of Dissimilar AISI 1045/S235JR Steels Welded by Automated GMAW. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji. 2026. doi:10.29109/gujsc.2034682
BibTeX
@article{Kutepe2026,
author = {Kuştepe, Kaan and Kursun, Betül Demirci and Güler, Ebru Saraloğlu},
title = {Experimental and Numerical Investigation of Dissimilar AISI 1045/S235JR Steels Welded by Automated GMAW},
journal = {Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji},
year = {2026},
number = {Advanced Online Publication},
doi = {10.29109/gujsc.2034682}
}
EUVIMED