Separation and Transition on the ROTEX-T Cone–Flare
AIAA Journal · 2025-09 · 63 (9) · 3939-3966
DOI: 10.2514/1.j064190 ↗Kurz gefasst
Fachartikel in der Zeitschrift AIAA Journal, 2025-09. Verfasst von Jonathan Davami und 12 weiteren Autor:innen. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 101 Literaturangaben. Gefördert von: Air Force Research Laboratory, Air Force Office of Scientific Research, University of Notre Dame Dean's Fellowship.
Abstract (Originalsprache)
Coordinated experimental and computational studies were conducted on the ROTEX-T, a cone–flare geometry used in a successful flight-test experiment, with the objectives of explaining the origins of the largest differences between computational and experimental results, assessing code-to-code, facility-to-facility, and ground-to-flight differences, and further illuminating the flight-test results. Background-oriented schlieren, infrared thermography, high-speed self-aligned focusing schlieren, and focused laser differential interferometry measurements were made in two wind tunnels. The surface heat flux and Stanton number distributions were calculated. Separation and reattachment locations, as well as flow state at each, were determined. Computational results were obtained using the VULCAN-CFD and SU2 codes in steady-state mode, and direct numerical simulation (DNS). The nominally steady axisymmetric flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Without adding external noise, the disturbance amplitudes computed by DNS were found to be high in the separation bubble, and thus the flow was transitional. The separation location predicted computationally is consistently upstream of the experimental observation. This difference is caused by tunnel noise, whose effect is not incorporated into the computations. Despite this, the computed density field and shape of the separation bubble closely matched that observed experimentally. The maximum vertical density gradient was confirmed as an accurate, very useful definition of the boundary-layer edge. Computed laminar heating rates before separation agreed well with experiment; transitional heating rates after reattachment from experiments were between laminar and turbulent computations. Reattachment location and the flow state upon reattachment were assessed for the flight data. At flight-matched Reynolds numbers, flight trends align with the ground-test results, indicating a transitional shock-wave/boundary-layer interaction. ‡‡‡
Förderung
- Air Force Research Laboratory
- Air Force Office of Scientific Research
- University of Notre Dame Dean's Fellowship
- Office of Naval Research
- Aeronautics Research Mission Directorate
- Langley Research Center
Zitieren
APA
Davami, J., Juliano, T. J., Scholten, A., Paredes, P., Benitez, E. K., Running, C. L., Little, N., Duan, L., Dylewicz, K., Pezlar, V., Theofilis, V., Thiele, T., & Willems, S. (2025). Separation and Transition on the ROTEX-T Cone–Flare. AIAA Journal, 63(9), 3939-3966. https://doi.org/10.2514/1.j064190
Vancouver
Davami J, Juliano TJ, Scholten A, Paredes P, Benitez EK, Running CL, et al. Separation and Transition on the ROTEX-T Cone–Flare. AIAA Journal. 2025;63(9):3939-3966. doi:10.2514/1.j064190
BibTeX
@article{Davami2025,
author = {Davami, Jonathan and Juliano, Thomas J. and Scholten, Anton and Paredes, Pedro and Benitez, Elizabeth K. and Running, Carson L. and Little, Nolan and Duan, Lian and Dylewicz, Kamil and Pezlar, Vojtech and Theofilis, Vassilis and Thiele, Thomas and Willems, Sebastian},
title = {Separation and Transition on the ROTEX-T Cone–Flare},
journal = {AIAA Journal},
year = {2025},
volume = {63},
number = {9},
pages = {3939--3966},
doi = {10.2514/1.j064190}
}
EUVIMED