EUVIMEDEUVIMED entdecken
Crossref

Numerical Investigation of The Influence of Adhesive Layer Thickness, Fillet Geometry And Reinforcement on The Creep Behavior of Single Lap Joint

Somnath Somadder, Muhammad Ullah, A B M Mahir Faisal, Muhammad Jawad Zin Noor, Md. Mahbubur Rahman, Md Ashraful Islam

International Journal of Engineering and Applied Sciences · 30.06.2026 · 18 (1)

DOI: 10.24107/ijeas.1856017 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Engineering and Applied Sciences, online erschienen am 30.06.2026. Verfasst von Somnath Somadder und 5 weiteren Autor:innen. Die Arbeit nennt 39 Literaturangaben. Gefördert von: None.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Adhesive joints are widely used in the automotive, aerospace, and construction industries because they distribute loads uniformly, join dissimilar materials, and reduce structural weight. However, their long-term performance is strongly affected by creep, the time-dependent deformation of the adhesive layer under sustained loading, which can compromise joint integrity. This study presents a systematic numerical investigation of the combined effects of adhesive layer thickness, fillet geometry, and material reinforcement on the creep behavior of adhesively bonded single lap joints. Finite element simulations were performed in Abaqus using the Norton-Bailey power-law constitutive model, with validation against published results showing a maximum deviation below 7.5%. Four adhesive thicknesses (0.25-0.55 mm) were analyzed at both the elastic (t = 0.1 s) and creep-dominant (t = 4 h) stages. The results show that increasing adhesive thickness reduces peak shear stress and creep strain by approximately 15-25% and 20-30%, respectively, by promoting a more uniform load transfer along the overlap. The introduction of fillets at the overlap edges further mitigates stress concentration, yielding an additional 10-20% reduction in peak stress and strain. Carbon-fiber reinforcement of the adhesive produces the most pronounced improvement, decreasing peak creep strain by 44.68% for Epoxy A and 24.37% for Epoxy B. These findings provide design-level insights for enhancing the long-term durability of adhesively bonded joints through combined geometric and material optimization.

Förderung

  • None

Zitieren

APA

Somadder, S., Ullah, M., Faisal, A. B. M. M., Noor, M. J. Z., Rahman, M. M., & Islam, M. A. (2026). Numerical Investigation of The Influence of Adhesive Layer Thickness, Fillet Geometry And Reinforcement on The Creep Behavior of Single Lap Joint. International Journal of Engineering and Applied Sciences, 18(1). https://doi.org/10.24107/ijeas.1856017

Vancouver

Somadder S, Ullah M, Faisal ABMM, Noor MJZ, Rahman MM, Islam MA. Numerical Investigation of The Influence of Adhesive Layer Thickness, Fillet Geometry And Reinforcement on The Creep Behavior of Single Lap Joint. International Journal of Engineering and Applied Sciences. 2026;18(1). doi:10.24107/ijeas.1856017

BibTeX
@article{Somadder2026,
  author = {Somadder, Somnath and Ullah, Muhammad and Faisal, A B M Mahir and Noor, Muhammad Jawad Zin and Rahman, Md. Mahbubur and Islam, Md Ashraful},
  title = {Numerical Investigation of The Influence of Adhesive Layer Thickness, Fillet Geometry And Reinforcement on The Creep Behavior of Single Lap Joint},
  journal = {International Journal of Engineering and Applied Sciences},
  year = {2026},
  volume = {18},
  number = {1},
  doi = {10.24107/ijeas.1856017}
}
Kostenlos starten →