EUVIMEDEUVIMED entdecken
Crossref

RESEARCH ON THE UNEVENNESS OF THE DELIVERY OF BULK MATERIALS BY A DISC

Vasyl Banha, Ihor Dmytriv, Oleh-Solomon Kozak

Ukrainian Journal of Mechanical Engineering and Materials Science · 2026 · 12 (3) · 77-87

DOI: 10.23939/ujmems2026.03.077 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Ukrainian Journal of Mechanical Engineering and Materials Science, 2026. Verfasst von Vasyl Banha und 2 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ensuring stable and uniform delivery of bulk materials remains an important challenge for dosing equipment used in agricultural, mechanical engineering, pharmaceutical, chemical, and processing industries. The quality of dosing is determined not only by the average material flow rate but also by the stability of delivery and the process's ability to remain within the specified technological tolerance. Insufficient uniformity of material output can reduce process reliability and adversely affect the quality of the final product. The objective of this study was to experimentally determine the influence of the main design and operating parameters of a centrifugal conical-disc dispenser on the uniformity of bulk-material delivery and on the probability of maintaining the dosing process within the technological tolerance. The experimental studies were carried out using an improved laboratory test stand equipped with strain-gauge measuring devices to record bulk material flow. A planned two-factor experiment at three levels was applied. The rotational frequency of the conical disc and the angle of the cone generatrix at its base were selected as the variable factors, while the disc diameter and the annular gap between the hopper outlet and the working body were kept constant. The rotational frequency was varied from 0.28 to 1.39 rad/s, and the cone angle from 0 to 20°. The delivery unevenness and the probability of the random dosing process remaining within the technological tolerance were used as the response criteria. Based on the experimental data, regression models describing the influence of the investigated factors were obtained. The reproducibility and adequacy of the experimental results were verified statistically. The calculated values of the Cochrane criterion were 0.27 and 0.26, which were lower than the tabulated value of 0.4775. The corresponding Fisher criterion values were 1.5 and 0.45, both below the critical value of 2.101. These results confirmed the reproducibility of the experiments and the adequacy of the developed regression models. The experimental results showed that increasing the rotational frequency of the conical disc and the angle of the cone generatrix generally improved the stability of bulk-material dosing. At a rotational frequency of 1.39 rad/s, increasing the cone angle from 0 to 20° reduced the delivery unevenness from 7.43% to 6.10%. At a rotational frequency of approximately 0.83 rad/s, increasing the cone angle from 0 to 20° increased the probability of remaining within the technological tolerance from 0.221 to 0.281. The maximum probability of 0.377 was obtained at a cone angle of 20° and a rotational frequency of 1.39 rad/s. Under the investigated operating conditions, the delivery unevenness ranged from 6.10 to 7.43%, while the probability of maintaining the process within the technological tolerance ranged from 0.297 to 0.377. The results obtained provide an experimental basis for selecting rational geometric and operating parameters for centrifugal conical-disc dispensers. The established relationships can be used to further optimize dispenser design, improve dosing uniformity, and enhance the stability and reliability of bulk-material feeding processes.

Zitieren

APA

Banha, V., Dmytriv, I., & Kozak, O. (2026). RESEARCH ON THE UNEVENNESS OF THE DELIVERY OF BULK MATERIALS BY A DISC. Ukrainian Journal of Mechanical Engineering and Materials Science, 12(3), 77-87. https://doi.org/10.23939/ujmems2026.03.077

Vancouver

Banha V, Dmytriv I, Kozak O. RESEARCH ON THE UNEVENNESS OF THE DELIVERY OF BULK MATERIALS BY A DISC. Ukrainian Journal of Mechanical Engineering and Materials Science. 2026;12(3):77-87. doi:10.23939/ujmems2026.03.077

BibTeX
@article{Banha2026,
  author = {Banha, Vasyl and Dmytriv, Ihor and Kozak, Oleh-Solomon},
  title = {RESEARCH ON THE UNEVENNESS OF THE DELIVERY OF BULK MATERIALS BY A DISC},
  journal = {Ukrainian Journal of Mechanical Engineering and Materials Science},
  year = {2026},
  volume = {12},
  number = {3},
  pages = {77--87},
  doi = {10.23939/ujmems2026.03.077}
}
Kostenlos starten →