EUVIMEDEUVIMED entdecken
Crossref

Mechanical properties of a polymethyl methacrylate block for CAD/CAM dentures

Maiko Iwaki, Manabu Kanazawa, Toshio Arakida, Shunsuke Minakuchi

Journal of Oral Science · 2020 · 62 (4) · 420-422

DOI: 10.2334/josnusd.19-0448 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Oral Science, 2020. Verfasst von Maiko Iwaki und 3 weiteren Autor:innen. Beteiligte Einrichtung: General Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University. Hauptthemen laut MEDLINE: Computer-Aided Design, Polymethyl Methacrylate. Die Arbeit wurde bisher 56-mal zitiert (Crossref) und nennt 27 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study compared the mechanical properties and molecular distribution of a polymethyl methacrylate (PMMA) block (Dry) with specimens that were fabricated by a conventional method and cured in a wet environment (Control). Two specimen types were fabricated with heat-curing denture base resin. Dry specimens were polymerized at high pressure and in a dry system, while Control specimens were polymerized with a heat-curing method, in accordance with the manufacturer's recommended procedures. Specimens from each group were evaluated for three-point bending, water sorption and solubility, and color change, and by gel permeation chromatography (GPC). Mean values for the flexural strengths and moduli of the Dry specimens were significantly higher than those of the Control specimens (P > 0.05). Water sorption and discoloration values of the Dry group were significantly lower than those of the Control group. Mean weight-average molecular weights of the Dry group were higher than those of the Control group. As compared with the conventional method, the present method of fabricating PMMA blocks under high pressure yields superior mechanical properties for the denture base.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignPolymethyl MethacrylateDenture BasesDenturesMaterials TestingStress, MechanicalSurface Properties

Stichwörter der Autor:innen

CAD/CAMPMMAdenture basemechanical propertiesmolecular distribution

Substanzen

Polymethyl Methacrylate

Autor:innen und Institutionen

  • General Dentistry, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University.
  • Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University.

Zitieren

APA

Iwaki, M., Kanazawa, M., Arakida, T., & Minakuchi, S. (2020). Mechanical properties of a polymethyl methacrylate block for CAD/CAM dentures. Journal of Oral Science, 62(4), 420-422. https://doi.org/10.2334/josnusd.19-0448

Vancouver

Iwaki M, Kanazawa M, Arakida T, Minakuchi S. Mechanical properties of a polymethyl methacrylate block for CAD/CAM dentures. Journal of Oral Science. 2020;62(4):420-422. doi:10.2334/josnusd.19-0448

BibTeX
@article{Iwaki2020,
  author = {Iwaki, Maiko and Kanazawa, Manabu and Arakida, Toshio and Minakuchi, Shunsuke},
  title = {Mechanical properties of a polymethyl methacrylate block for CAD/CAM dentures},
  journal = {Journal of Oral Science},
  year = {2020},
  volume = {62},
  number = {4},
  pages = {420--422},
  doi = {10.2334/josnusd.19-0448}
}
Kostenlos starten →