EUVIMEDEUVIMED entdecken
Crossref

Influence of residual ridge morphology and manufacturing methods on the trueness of digitally fabricated denture bases of the mandible

Atsuo Nakanishi, Yutaro Oyamada, Yuka Sasaki, Kazuhiro Kon

Journal of Prosthodontic Research · 2026 · 70 (3) · 433-440

DOI: 10.2186/jpr.jpr_d_25_00085 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2026. Verfasst von Atsuo Nakanishi und 3 weiteren Autor:innen. Beteiligte Einrichtung: Division of Fixed Prosthodontics and Oral Implantology, Department of Prosthodontics, Faculty of Dental Medicine, Iwate Medical University, Morioka, …. Hauptthemen laut MEDLINE: Computer-Aided Design, Denture Design, Denture Bases, Mandible. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 50 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: To evaluate the trueness of denture bases fabricated using digital light processing (DLP) and milling methods using three-dimensional (3D) models with varying residual ridge morphologies. METHODS: Edentulous mandibular 3D models representing a well-rounded ridge (WR), knife-edge ridge (KR), and flat ridge (FR) were designed using computer-aided design (CAD) software. Denture bases for these models were created using dental CAD software and fabricated via DLP 3D printing at build angles of 0 and 45 degrees (DLP0 and DLP45) and by milling (MIL). A total of 90 denture bases were fabricated, with 10 bases per model-method combination. These bases were digitized and compared to their original CAD data to assess the adaptation across three regions: denture border, alveolar ridge, and retromolar pad. Measurements were performed at three time points: before water storage, after 1 day of water storage, and after 7 days of water storage. RESULTS: The MIL bases exhibited significantly lower 3D surface deviations than the DLP0 and DLP45 bases. The KR models generally exhibited greater 3D surface deviations than the WR and FR models. Temporal changes in the denture bases were significant across almost all ridge types and manufacturing methods. CONCLUSIONS: The trueness of digitally fabricated denture bases is influenced by the residual ridge morphology and manufacturing method. Milling demonstrated superior trueness compared to DLP. Temporal dimensional changes were observed in almost all the bases.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignDenture DesignDenture BasesMandibleAlveolar ProcessPrinting, Three-DimensionalHumansSoftwareModels, DentalJaw, Edentulous

Stichwörter der Autor:innen

3D printingDigital light processingMillingRemovable complete dentureResidual ridge resorption

Autor:innen und Institutionen

  • Division of Fixed Prosthodontics and Oral Implantology, Department of Prosthodontics, Faculty of Dental Medicine, Iwate Medical University, Morioka, Japan.

Zitieren

APA

Nakanishi, A., Oyamada, Y., Sasaki, Y., & Kon, K. (2026). Influence of residual ridge morphology and manufacturing methods on the trueness of digitally fabricated denture bases of the mandible. Journal of Prosthodontic Research, 70(3), 433-440. https://doi.org/10.2186/jpr.jpr_d_25_00085

Vancouver

Nakanishi A, Oyamada Y, Sasaki Y, Kon K. Influence of residual ridge morphology and manufacturing methods on the trueness of digitally fabricated denture bases of the mandible. Journal of Prosthodontic Research. 2026;70(3):433-440. doi:10.2186/jpr.jpr_d_25_00085

BibTeX
@article{Nakanishi2026,
  author = {Nakanishi, Atsuo and Oyamada, Yutaro and Sasaki, Yuka and Kon, Kazuhiro},
  title = {Influence of residual ridge morphology and manufacturing methods on the trueness of digitally fabricated denture bases of the mandible},
  journal = {Journal of Prosthodontic Research},
  year = {2026},
  volume = {70},
  number = {3},
  pages = {433--440},
  doi = {10.2186/jpr.jpr_d_25_00085}
}
Kostenlos starten →