EUVIMEDEUVIMED entdecken
Crossref

Thermal stress behavior of monolithic zirconia crowns with different thicknesses

Kohei Komine, Natsuko Murakami, Junichiro Wada, Toshiki Yamazaki, Li Bin, Miona Utsumi, Shiqi Zou, Noriyuki Wakabayashi

Journal of Prosthodontic Research · 2025

DOI: 10.2186/jpr.jpr_d_24_00212 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2025. Verfasst von Kohei Komine und 7 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Prosthodontics, Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan. Hauptthemen laut MEDLINE: Crowns, Zirconium, Dental Stress Analysis, Stress, Mechanical. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 46 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: This study was aimed at investigating the thermal stresses in monolithic zirconia crowns (MZC) of various thicknesses and elucidating their thermal behavior under cooling or heating changes in the oral cavity. Additionally, the clinical availability and potential issues of MZC were examined by comparing them with other crown materials. METHODS: Finite element models comprising MZC (0.5-, 1.0-, and 1.5-mm thick), cement layers, and abutment teeth were subjected to thermal changes from 37 to 5 °C or 60 °C. Using a thermal distribution at 5 s, the thermal stress was calculated and compared with those of gold alloy and resin composite crowns. The loads corresponding to the thermal stresses were also estimated by comparing them with the stresses induced by vertical loading on the occlusal surface. RESULTS: Tensile stress occurred primarily in the crowns and cement during cooling, whereas compressive stress was generated during heating. Thermal stresses increased from 16.0 to 27.2 MPa with decreasing crown thickness from 1.5 to 0.5 mm and varied with different materials. Although the MZC exhibited the highest thermal stress, the estimated load (200 N) corresponding to the thermal stress was smaller than that of the resin composite (1280 N). CONCLUSIONS: Thinner crowns exhibited higher thermal stress, suggesting an increased risk of failure owing to thermal changes. Despite the higher thermal stress in thinner MZC, the stresses were below the fatigue strength of the material, indicating sufficient resistance to thermal changes in the oral cavity.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsZirconiumDental Stress AnalysisStress, MechanicalDental MaterialsTemperatureFinite Element AnalysisMaterials TestingComposite ResinsHot TemperatureHumans

Stichwörter der Autor:innen

CrownFinite element analysisThermal stressZirconia

Substanzen

Zirconiumzirconium oxideDental MaterialsComposite Resins

Autor:innen und Institutionen

  • Advanced Prosthodontics, Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.

Zitieren

APA

Komine, K., Murakami, N., Wada, J., Yamazaki, T., Bin, L., Utsumi, M., Zou, S., & Wakabayashi, N. (2025). Thermal stress behavior of monolithic zirconia crowns with different thicknesses. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_24_00212

Vancouver

Komine K, Murakami N, Wada J, Yamazaki T, Bin L, Utsumi M, et al. Thermal stress behavior of monolithic zirconia crowns with different thicknesses. Journal of Prosthodontic Research. 2025. doi:10.2186/jpr.jpr_d_24_00212

BibTeX
@article{Komine2025,
  author = {Komine, Kohei and Murakami, Natsuko and Wada, Junichiro and Yamazaki, Toshiki and Bin, Li and Utsumi, Miona and Zou, Shiqi and Wakabayashi, Noriyuki},
  title = {Thermal stress behavior of monolithic zirconia crowns with different thicknesses},
  journal = {Journal of Prosthodontic Research},
  year = {2025},
  doi = {10.2186/jpr.jpr_d_24_00212}
}
Kostenlos starten →