EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 3.0

Tensile and Tear Strength Evaluation of Clean-Grade Silicone with Cellulose Nanocrystals Reinforcement as an Alternative Material for Maxillofacial Prostheses: An Experimental Study

Sara Stefany, An-Nissa Kusumadewi iD, Lisda Damayanti iD, Veni Takarini iD

Medical Devices: Evidence and Research · 2026-07 · Volume 19 · 1-14

DOI: 10.2147/mder.s621954 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Medical Devices: Evidence and Research, 2026-07. Verfasst von Sara Stefany und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Universitas Padjadjaran, Bandung, Indonesia. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 3.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Silicone elastomers are widely used in maxillofacial prostheses owing to their elasticity, esthetic properties, and biocompatibility. Clean-grade silicone serves as an affordable alternative to medical-grade silicone. The addition of Cellulose Nanocrystals (CNC) and intrinsic pigments is expected to enhance the performance of clean-grade silicone.

Purpose

This study aims to evaluate the effects of CNC and intrinsic pigments on the tensile strength, elongation percentage, and tear strength of clean-grade silicone as an alternative material for maxillofacial prostheses. Materials and Methods: Six groups of clean-grade silicone were evaluated: control, A (with pigment), B (with 0.5% CNC), C (with 0.5% CNC and pigment), D (with 1% CNC), and E (with 1% CNC and pigment). Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) were conducted to evaluate the morphological and functional group characteristics; tensile strength, elongation percentage, and tear strength were measured to assess changes in mechanical properties and were analyzed statistically.

Results

SEM analysis showed microstructure formation characterized by dispersed particles with the addition of 1% CNC and intrinsic pigments. As the filler and pigment were added, the FTIR revealed increased absorption intensities of Si-O-Si functional groups, detected at 1022– 1026 cm − 1 . The tensile trength (3.87– 4.84 MPa) was successfully increased compared to the control group (3.63 MPa), a statistically significant difference (p< 0.05). Group D had the highest tensile strength, aligning closely with medical-grade silicone (approximately 2.53– 8.36 MPa). Meanwhile, the lowest elongation percentage and the highest tear strength (3.84 kN/m) resulted in Group E, both of which are close to the range of maxillofacial prosthesis requirements.

Conclusion

The addition of 1% CNC and intrinsic pigments successfully increased tensile and tear strength while reducing the elongation percentage of clean-grade silicone that potential as an alternative material; however, future optimization on the tear strength still required before maxillofacial prosthesis application. Keywords: cellulose nanocrystals, intrinsic pigment, tensile and tear strength, elongation percentage, clean-grade silicone, alternative maxillofacial prosthesis

Schlagwörter

Stichwörter der Autor:innen

alternative maxillofacial prosthesiscellulose nanocrystalsclean-grade siliconeelongation percentageintrinsic pigmenttensile and tear strength

Autor:innen und Institutionen

  • Faculty of Dentistry, Universitas Padjadjaran, Bandung, Indonesia.
  • Prosthodontics Department, Faculty of Dentistry, Universitas Padjadjaran, Bandung, Indonesia.
  • Dental Materials and Technology Department, Faculty of Dentistry, Universitas Padjadjaran, Bandung, Indonesia.

ORCID-Profile: An-Nissa Kusumadewi, Lisda Damayanti, Veni Takarini

Zitieren

APA

Stefany, S., Kusumadewi, A. N., Damayanti, L., & Takarini, V. (2026). Tensile and Tear Strength Evaluation of Clean-Grade Silicone with Cellulose Nanocrystals Reinforcement as an Alternative Material for Maxillofacial Prostheses: An Experimental Study. Medical Devices: Evidence and Research, Volume 19, 1-14. https://doi.org/10.2147/mder.s621954

Vancouver

Stefany S, Kusumadewi AN, Damayanti L, Takarini V. Tensile and Tear Strength Evaluation of Clean-Grade Silicone with Cellulose Nanocrystals Reinforcement as an Alternative Material for Maxillofacial Prostheses: An Experimental Study. Medical Devices: Evidence and Research. 2026;Volume 19:1-14. doi:10.2147/mder.s621954

BibTeX
@article{Stefany2026,
  author = {Stefany, Sara and Kusumadewi, An-Nissa and Damayanti, Lisda and Takarini, Veni},
  title = {Tensile and Tear Strength Evaluation of Clean-Grade Silicone with Cellulose Nanocrystals Reinforcement as an Alternative Material for Maxillofacial Prostheses: An Experimental Study},
  journal = {Medical Devices: Evidence and Research},
  year = {2026},
  volume = {Volume 19},
  pages = {1--14},
  doi = {10.2147/mder.s621954}
}
Kostenlos starten →