Laser-induced Forward Transfer Hydrogel Printing: A Defined Route for Highly Controlled Process
International Journal of Bioprinting · 02.08.2024 · 6 (3) · 271
DOI: 10.18063/ijb.v6i3.271 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Bioprinting, online erschienen am 02.08.2024. Verfasst von Vladimir Yusupov und 7 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Photon Technologies, Federal Scientific Research Centre "Crystallography and Photonics," Russian Academy of Sciences, Pionerskaya 2, Tro…. Die Arbeit wurde bisher 61-mal zitiert (Crossref). Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).
Abstract (Originalsprache)
Laser-induced forward transfer is a versatile, non-contact, and nozzle-free printing technique which has demonstrated high potential for different printing applications with high resolution. In this article, three most widely used hydrogels in bioprinting (2% hyaluronic acid sodium salt, 1% methylcellulose, and 1% sodium alginate) were used to study laser printing processes. For this purpose, the authors applied a laser system based on a pulsed infrared laser (1064 nm wavelength, 8 ns pulse duration, 1 – 5 J/ cm2 laser fluence, and 30 μm laser spot size). A high-speed shooting showed that the increase in fluence caused a sequential change in the transfer regimes: No transfer regime, optimal jetting regime with a single droplet transfer, high speed regime, turbulent regime, and plume regime. It was demonstrated that in the optimal jetting regime, which led to printing with single droplets, the size and volume of droplets transferred to the acceptor slide increased almost linearly with the increase of laser fluence. It was also shown that the maintenance of a stable temperature (±2°C) allowed for neglecting the temperature-induced viscosity change of hydrogels. It was determined that under room conditions (20°C, humidity 50%), the hydrogel layer, due to drying processes, decreased with a speed of about 8 μm/min, which could lead to a temporal variation of the transfer process parameters. The authors developed a practical algorithm that allowed quick configuration of the laser printing process on an applied experimental setup. The configuration is provided by the change of the easily tunable parameters: Laser pulse energy, laser spot size, the distance between the donor ribbon and acceptor plate, as well as the thickness of the hydrogel layer on the donor ribbon slide.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute of Photon Technologies, Federal Scientific Research Centre "Crystallography and Photonics," Russian Academy of Sciences, Pionerskaya 2, Troitsk, Moscow, 108840, Russia.
- Institute for Regenerative Medicine, Sechenov First Moscow State Medical University, 8-2 Trubetskaya st., Moscow, 119991, Russia.
- Center for Design Manufacturing and Materials, Skolkovo Institute of Science and Technology, Bolshoy Boulevard 30, Bld. 1, Moscow, 121205, Russia.
- Department of Polymers and Composites, N.N.Semenov Institute of Chemical Physics, 4 Kosygin St., Moscow, 119991, Russia.
- Department of Chemistry, Lomonosov Moscow State University, Leninskiye Gory 1‑3, Moscow 119991, Russia.
Zitieren
APA
Yusupov, V., Churbanov, S., Churbanova, E., Bardakova, K., Antoshin, A., Evlashin, S., Timashev, P., & Minaev, N. (2024). Laser-induced Forward Transfer Hydrogel Printing: A Defined Route for Highly Controlled Process. International Journal of Bioprinting, 6(3), 271. https://doi.org/10.18063/ijb.v6i3.271
Vancouver
Yusupov V, Churbanov S, Churbanova E, Bardakova K, Antoshin A, Evlashin S, et al. Laser-induced Forward Transfer Hydrogel Printing: A Defined Route for Highly Controlled Process. International Journal of Bioprinting. 2024;6(3):271. doi:10.18063/ijb.v6i3.271
BibTeX
@article{Yusupov2024,
author = {Yusupov, Vladimir and Churbanov, Semyon and Churbanova, Ekaterina and Bardakova, Ksenia and Antoshin, Artem and Evlashin, Stanislav and Timashev, Peter and Minaev, Nikita},
title = {Laser-induced Forward Transfer Hydrogel Printing: A Defined Route for Highly Controlled Process},
journal = {International Journal of Bioprinting},
year = {2024},
volume = {6},
number = {3},
pages = {271},
doi = {10.18063/ijb.v6i3.271}
}
EUVIMED