EUVIMEDEUVIMED entdecken
Crossref

SYNTHESIS AND CHARACTERIZATION OF CATIO3-REINFORCED CHITOSAN COATINGS FOR ENHANCED CORROSION RESISTANCE

Nihan Ercioğlu Akdoğan, Emre Akdoğan

Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering · 25.06.2026 · 27 (2) · 302-337

DOI: 10.18038/estubtda.1863748 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering, online erschienen am 25.06.2026. Verfasst von Nihan Ercioğlu Akdoğan und 1 weiteren Autor:innen. Die Arbeit nennt 25 Literaturangaben. Gefördert von: Eskisehir Technical University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, chitosan-based composite coatings modified with calcium titanate particles were investigated in terms of their microstructural characteristics and corrosion resistance. Chitosan gels containing 0–2 wt.% calcium titanate were prepared, and the morphology of the resulting composites was examined using scanning electron microscopy. Fourier transform infrared analysis showed that the incorporation of calcium titanate particles into the chitosan matrix caused changes in the intensity of the characteristic hydroxyl, amine, and ether bands, indicating physical interactions between the particles and the polymer chains without the formation of new chemical bonds. The results demonstrated that calcium titanate particles were more uniformly dispersed within the chitosan matrix at low filler contents, while higher particle concentrations led to pronounced agglomeration. Among the investigated compositions, the composite containing 0.05 wt.% calcium titanate exhibited the most homogeneous microstructure with minimal particle aggregation. Based on these findings, the optimized composite formulation was applied onto metal substrates using the layer-by-layer deposition method to produce two-layer coatings. The corrosion behavior of uncoated and coated metal samples was evaluated by immersion in a saline solution for one week. Severe corrosion was observed on the uncoated metal surface, whereas no significant corrosion or surface degradation was detected on the coated samples containing calcium titanate. In addition, the particles were uniformly distributed on the coating surface without noticeable aggregation. Particle size analysis of calcium titanate powders revealed an average particle size of 1.81 micrometers, consistent with particle size distribution measurements. Overall, the results indicate that calcium titanate-modified chitosan coatings form an effective protective barrier and significantly enhance corrosion resistance in saline environments.

Förderung

  • Eskisehir Technical University

Zitieren

APA

Akdoğan, N. E., & Akdoğan, E. (2026). SYNTHESIS AND CHARACTERIZATION OF CATIO3-REINFORCED CHITOSAN COATINGS FOR ENHANCED CORROSION RESISTANCE. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering, 27(2), 302-337. https://doi.org/10.18038/estubtda.1863748

Vancouver

Akdoğan NE, Akdoğan E. SYNTHESIS AND CHARACTERIZATION OF CATIO3-REINFORCED CHITOSAN COATINGS FOR ENHANCED CORROSION RESISTANCE. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering. 2026;27(2):302-337. doi:10.18038/estubtda.1863748

BibTeX
@article{Akdoan2026,
  author = {Akdoğan, Nihan Ercioğlu and Akdoğan, Emre},
  title = {SYNTHESIS AND CHARACTERIZATION OF CATIO3-REINFORCED CHITOSAN COATINGS FOR ENHANCED CORROSION RESISTANCE},
  journal = {Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering},
  year = {2026},
  volume = {27},
  number = {2},
  pages = {302--337},
  doi = {10.18038/estubtda.1863748}
}
Kostenlos starten →