EUVIMEDEUVIMED entdecken
Crossref

Atomic Force Microscopic Investigations of Improved Wetting Behavior of the Graphene Coated Copper Substrate by Novel Spray Coating Method

Sudhakar Giri, Arun Autee, Abhijeet Kadam, Ankush Khansole

Indian Journal Of Science And Technology · 11.06.2026 · 19 (20) · 1384-1396

DOI: 10.17485/ijst/v19i20.686 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Indian Journal Of Science And Technology, online erschienen am 11.06.2026. Verfasst von Sudhakar Giri und 3 weiteren Autor:innen.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To perform and analyze the characterization of graphene and its coating on a copper substrate, and to investigate the improvement in the wetting behavior of the coated copper substrate through a morphological study after graphene coating.

Method

Graphene was characterized by XRD, Raman spectroscopy, and SEM before preparing the xylene and IPA-assisted colloidal spray solution. This spray solution was used to coat a 2 mm-thick, 25.4 mm-diameter copper disc. The coated metal disc was further characterized by XRD, Raman spectroscopy, AFM, and contact angle measurements.

Findings

Advanced characterization techniques revealed the full spectral profile of graphene. The number of graphene layers calculated from XRD analysis is 5-6, indicating the use of a few-layer graphene sample in this study. D, G, and 2D band have peaks at 1357 cm-1, 1593 cm-1, and 2670 cm-1, respectively. SEM and AFM studies revealed the surface morphology of the graphene coating on the copper substrate. The wettability behavior of the bare Cu surface and the graphene-coated Cu (Gr@Cu) surface was examined. For the bare Cu surface, the contact angles were measured, yielding an average of approximately 93°, indicating a slightly hydrophobic nature. In contrast, the Gr@Cu surface exhibited significantly higher contact angles, with an average of about 104°, indicating enhanced hydrophobic behavior. This increase in contact angle after graphene coating is attributed to the unique surface morphology of graphene sheets, which introduces micro- and nanoscale roughness and lowers surface energy. Contact angle measurements indicated a shift in the surface's wetting behavior. These findings are useful for promoting drop-wise condensation in heat exchangers. Novelty: This study demonstrates the application of a simple, mass-scalable, in-situ solution spray-coating method for the surface functionalization of metal substrates and investigates wetting insights after surface functionalization using AFM. Keywords: Graphene, Heat exchanger, spray coating, Xylene, hydrophobic, AFM

Zitieren

APA

Giri, S., Autee, A., Kadam, A., & Khansole, A. (2026). Atomic Force Microscopic Investigations of Improved Wetting Behavior of the Graphene Coated Copper Substrate by Novel Spray Coating Method. Indian Journal Of Science And Technology, 19(20), 1384-1396. https://doi.org/10.17485/ijst/v19i20.686

Vancouver

Giri S, Autee A, Kadam A, Khansole A. Atomic Force Microscopic Investigations of Improved Wetting Behavior of the Graphene Coated Copper Substrate by Novel Spray Coating Method. Indian Journal Of Science And Technology. 2026;19(20):1384-1396. doi:10.17485/ijst/v19i20.686

BibTeX
@article{Giri2026,
  author = {Giri, Sudhakar and Autee, Arun and Kadam, Abhijeet and Khansole, Ankush},
  title = {Atomic Force Microscopic Investigations of Improved Wetting Behavior of the Graphene Coated Copper Substrate by Novel Spray Coating Method},
  journal = {Indian Journal Of Science And Technology},
  year = {2026},
  volume = {19},
  number = {20},
  pages = {1384--1396},
  doi = {10.17485/ijst/v19i20.686}
}
Kostenlos starten →