EUVIMEDEUVIMED entdecken
Crossref

“Efficiency window” of dispersed particles in aluminum alloys: comparison of inert (ErF3) and reactive (W/Al12W) modifiers

Nikolay I. Kakhidze, Raul’ G. Mubarakov, Viktoriya D. Miroshkina, Anton P. Khrustalev, Vladimir V. Platov

Vestnik Tomskogo gosudarstvennogo universiteta. Matematika i mekhanika · 2026

DOI: 10.17223/19988621/101/8 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Vestnik Tomskogo gosudarstvennogo universiteta. Matematika i mekhanika, 2026. Verfasst von Nikolay I. Kakhidze und 4 weiteren Autor:innen.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper considers the dispersion strengthening of aluminum alloys with incoherent particles through the concept of a critical “efficiency window” bounded by the competition between strengthening mechanisms and defect/interface-related factors. Two model systems with contrasting behavior and processing routes are experimentally compared: the cast A359-ErF₃ alloy (as-cast and T6 heat-treated conditions) and the wrought AA5056-W alloy (as-cast and rolled conditions). For A359, the addition of 0.05-0.10 wt.% ErF₃ provides the most efficient strength-ductility balance both in the as-cast and T6 conditions, whereas concentrations > 0.3 wt.% decrease the ultimate tensile strength (σв) and elongation (εmax) due to particle agglomeration, increased microporosity, and interfacial decohesion. For AA5056-W, the optimum depends on the structural state: in the as-cast condition, maximum strength is achieved at 0.1 wt.% W, whereas after rolling it shifts to 0.3 wt.% W. At 0.5-0.8 wt.%, a decrease in σв and εmax, as well as a reduction in the strain-hardening reserve (σв - σ0.2), is observed. A parametric scheme for estimating the lower and upper boundaries of the “efficiency window” based on target structural scales (d, λ, L*) and geometric defect criteria (fm, fgap) is demonstrated. Comparison with available published data for A356-Al₂O₃ and AA6061-AlN confirms quantitative agreement between the calculated boundaries and the experimentally observed concentration optimum. The “efficiency window” approach is proposed as an engineering tool for selecting particle dosage and processing routes in dispersion-strengthened aluminum materials.

Zitieren

APA

Kakhidze, N. I., Mubarakov, R. G., Miroshkina, V. D., Khrustalev, A. P., & Platov, V. V. (2026). “Efficiency window” of dispersed particles in aluminum alloys: comparison of inert (ErF3) and reactive (W/Al12W) modifiers. Vestnik Tomskogo gosudarstvennogo universiteta. Matematika i mekhanika. https://doi.org/10.17223/19988621/101/8

Vancouver

Kakhidze NI, Mubarakov RG, Miroshkina VD, Khrustalev AP, Platov VV. “Efficiency window” of dispersed particles in aluminum alloys: comparison of inert (ErF3) and reactive (W/Al12W) modifiers. Vestnik Tomskogo gosudarstvennogo universiteta. Matematika i mekhanika. 2026. doi:10.17223/19988621/101/8

BibTeX
@article{Kakhidze2026,
  author = {Kakhidze, Nikolay I. and Mubarakov, Raul’ G. and Miroshkina, Viktoriya D. and Khrustalev, Anton P. and Platov, Vladimir V.},
  title = {“Efficiency window” of dispersed particles in aluminum alloys: comparison of inert (ErF3) and reactive (W/Al12W) modifiers},
  journal = {Vestnik Tomskogo gosudarstvennogo universiteta. Matematika i mekhanika},
  year = {2026},
  doi = {10.17223/19988621/101/8}
}
Kostenlos starten →