Integrating battery-like materials into supercapacitors
Electrochemical Materials and Technologies · 31.03.2026 · 5 (1) · 20254064
DOI: 10.15826/elmattech.2026.5.064 ↗Kurz gefasst
Fachartikel in der Zeitschrift Electrochemical Materials and Technologies, online erschienen am 31.03.2026. Verfasst von Cissan Adanma Sylvanus und 3 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
A binder-free composite hybrid electrode material was deposited through electrodeposition by combining carbon-based materials (graphene oxide) and battery like materials (NiO, ZnO and Al2O3) in a single electrode. The structural, morphological and electrochemical properties of CaAl2O4–ZnO/rGO composite thin film were studied to characterize the hybrid composites. The average crystallite size D of the hybrid composites is 23 nm with an average inter planar spacing of 1.90 Å and lattice constants (a = b = c = 1.456 Å) that reveal a rhombohedral structure. The introduction of Ni increases the cracks and nullifies the rod-like morphology of the undoped thin film while the presence of Ag reveals the nonexistence of cracks at lower concentrations of Ag dopant but densely packed homogenous noodle-like grains with cracks can be seen at a 0.03 M sample. EDX analysis confirmed the presence of deposited elements with the exception of Ag, and this could possibly be due to the low intensity of the Ag dopant or the low deposition voltage. Cyclic voltammetry curves show typical electrochemical behavior with clear oxidation and reduction peaks for most samples. The Nix = 0.06 doped CaAl2O4–ZnO/rGO composite thin films have the maximum specific capacitance of 673 F/g at a scan rate of 100 mV/s, while the Agx = 0.03 doped thin film has the minimum specific capacitance of 205 F/g at the same scan rate. indicating that NCZr3 has a good electrochemical behavior at 0.1 mA/g with an energy density and a power density of 59.83 W · h/Kg and 26.926 W · h/Kg, respectively. These results reveal the suitability of the Ni doped material as an electrode material for supercapacitor applications and confirm the model of roughening. Further studies should be explored by lowering scan rates (5–50 mV/s), adding binder materials, and properly varying Ag concentration and deposition time in order to explore more desirable properties for advanced applications.
Zitieren
APA
Sylvanus, C. A., Echendu, O. K., Anusionwu, B. C., & Eya, D. D. (2026). Integrating battery-like materials into supercapacitors. Electrochemical Materials and Technologies, 5(1), 20254064. https://doi.org/10.15826/elmattech.2026.5.064
Vancouver
Sylvanus CA, Echendu OK, Anusionwu BC, Eya DD. Integrating battery-like materials into supercapacitors. Electrochemical Materials and Technologies. 2026;5(1):20254064. doi:10.15826/elmattech.2026.5.064
BibTeX
@article{Sylvanus2026,
author = {Sylvanus, Cissan Adanma and Echendu, Obi Kingsley and Anusionwu, Bede Chinyere and Eya, Dominic D.O.},
title = {Integrating battery-like materials into supercapacitors},
journal = {Electrochemical Materials and Technologies},
year = {2026},
volume = {5},
number = {1},
pages = {20254064},
doi = {10.15826/elmattech.2026.5.064}
}
EUVIMED