EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation on cutting of CFRP composite by nanosecond short-pulsed laser with rotary drilling method

Liyuan Sheng, Xiangyu Cheng, Shilong Jiang, Chaochao Zhao, Jingdong Liu, Chenghu Jing, Jiale Wang, Liangjie Xu, Yinan Xiao, Bin Wang, Junke Jiao

Science and Engineering of Composite Materials · 12.02.2025 · 32 (1)

DOI: 10.1515/secm-2024-0047 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Science and Engineering of Composite Materials, online erschienen am 12.02.2025. Verfasst von Liyuan Sheng und 10 weiteren Autor:innen. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present research, the nanosecond short-pulsed laser with rotary drilling method was designed to process carbon fiber-reinforced polymer (CFRP) composite plate. The hole dimension, surface morphology, heat-affected zone (HAZ), and mechanical properties were analyzed. The results reveal that the CFRP composite plate could be rapidly drilled with highly qualified processing surface by the nanosecond short-pulsed laser with rotary drilling method. The figures such as circle, square, triangle, and regular hexagon could be processed with minimum hole diameter of 0.1 mm. The changing of laser scanning speed and laser power could result in the variation in diameter of hole entrance and exit, which fluctuates in scope of 35 μm. The calculated biggest taper angle is about 0.43°, but the smallest taper angle is about 0.12°. The laser drilling on CFPR composite decreases the tensile strength by about 9%, which should be ascribed to the damage of continuous carbon fiber, but it is still acceptable. The nanosecond short-pulsed laser with rotary drilling method generates a small HAZ on hole entrance but almost no HAZ in hole exit. The surface roughness of laser processed CFRP ranges from 2.925 to 4.226 μm. Comparatively, the laser scanning speed between 800 and 1,000 mm/s and laser power around 28 W would be the optimal choice, which could realize the best balance between surface quality and efficiency.

Zitieren

APA

Sheng, L., Cheng, X., Jiang, S., Zhao, C., Liu, J., Jing, C., Wang, J., Xu, L., Xiao, Y., Wang, B., & Jiao, J. (2025). Investigation on cutting of CFRP composite by nanosecond short-pulsed laser with rotary drilling method. Science and Engineering of Composite Materials, 32(1). https://doi.org/10.1515/secm-2024-0047

Vancouver

Sheng L, Cheng X, Jiang S, Zhao C, Liu J, Jing C, et al. Investigation on cutting of CFRP composite by nanosecond short-pulsed laser with rotary drilling method. Science and Engineering of Composite Materials. 2025;32(1). doi:10.1515/secm-2024-0047

BibTeX
@article{Sheng2025,
  author = {Sheng, Liyuan and Cheng, Xiangyu and Jiang, Shilong and Zhao, Chaochao and Liu, Jingdong and Jing, Chenghu and Wang, Jiale and Xu, Liangjie and Xiao, Yinan and Wang, Bin and Jiao, Junke},
  title = {Investigation on cutting of CFRP composite by nanosecond short-pulsed laser with rotary drilling method},
  journal = {Science and Engineering of Composite Materials},
  year = {2025},
  volume = {32},
  number = {1},
  doi = {10.1515/secm-2024-0047}
}
Kostenlos starten →