Non-woven textiles for medical implants: mechanical performances improvement
Biomedical Engineering / Biomedizinische Technik · 26.08.2022 · 67 (4) · 317-330
DOI: 10.1515/bmt-2022-0017 ↗Kurz gefasst
Fachartikel in der Zeitschrift Biomedical Engineering / Biomedizinische Technik, online erschienen am 25.05.2022. Verfasst von Amandine Lequeux und 3 weiteren Autor:innen. Beteiligte Einrichtung: Laboratoire de Physique et Mécanique Textiles (LPMT), ENSISA, Mulhouse, France. Hauptthemen laut MEDLINE: Prostheses and Implants, Textiles. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 46 Literaturangaben.
Abstract (Originalsprache)
Non-woven textile has been largely used as medical implant material over the last decades, especially for scaffold manufacturing purpose. This material presents a large surface area-to-volume ratio, which promotes adequate interaction with biological tissues. However, its strength is limited due to the lack of cohesion between the fibers. The goal of the present work was to investigate if a non-woven substrate can be reinforced by embroidery stitching towards strength increase. Non-woven samples were produced from both melt-blowing and electro-spinning techniques, reinforced with a stitching yarn and tested regarding several performances: ultimate tensile strength, burst strength and strength loss after fatigue stress. Several stitching parameters were considered: distance between stitches, number of stitch lines (1, 2 or 3) and line geometry (horizontal H, vertical L, cross X). The performance values obtained after reinforcement were compared with values obtained for control samples. Results bring out that reinforcement can increase the strength by up to 50% for a melt-blown mat and by up to 100% for an electro-spun mat with an X reinforcement pattern. However, after cyclic loading, the reinforcement yarn tends to degrade the ES mat in particular. Moreover, increasing the number of stitches tends to fragilize the mats.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratoire de Physique et Mécanique Textiles (LPMT), ENSISA, Mulhouse, France.
- The Nonwovens Institute, North Carolina State University, Raleigh, NC, USA.
- Département de Génie des Mines, de la Métallurgie et des Matériaux, Laboratoire d'Ingénierie de Surface, Centre de Recherche sur les Matériaux Avancés, Université Laval, Québec, Canada.
- Centre de Recherche du Centre Hospitalier Universitaire de Québec, Hôpital St-François d'Assise, Québec, Canada.
- Geprovas, Strasbourg, France.
ORCID-Profile: Frederic Heim
Zitieren
APA
Lequeux, A., Maze, B., Laroche, G., & Heim, F. (2022). Non-woven textiles for medical implants: mechanical performances improvement. Biomedical Engineering / Biomedizinische Technik, 67(4), 317-330. https://doi.org/10.1515/bmt-2022-0017
Vancouver
Lequeux A, Maze B, Laroche G, Heim F. Non-woven textiles for medical implants: mechanical performances improvement. Biomedical Engineering / Biomedizinische Technik. 2022;67(4):317-330. doi:10.1515/bmt-2022-0017
BibTeX
@article{Lequeux2022,
author = {Lequeux, Amandine and Maze, Benoit and Laroche, Gaetan and Heim, Frederic},
title = {Non-woven textiles for medical implants: mechanical performances improvement},
journal = {Biomedical Engineering / Biomedizinische Technik},
year = {2022},
volume = {67},
number = {4},
pages = {317--330},
doi = {10.1515/bmt-2022-0017}
}
EUVIMED