EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Design, modeling, and performance analysis of a 2-DOF pneumatic flexible wrist with controllable braking torque

Hongbo Liu iD, Shuo Wang, Wenpeng Xu

PLOS One · 11.11.2026 · 21 (11) · e0362364

DOI: 10.1371/journal.pone.0362364 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, online erschienen am 11.11.2026. Verfasst von Hongbo Liu und 2 weiteren Autor:innen. Beteiligte Einrichtung: Engineering Training Center, Beihua University, Jilin, Jilin, China. Hauptthemen laut MEDLINE: Robotics, Wrist, Wrist Joint. Die Arbeit nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Jilin Province Science and Technology Development Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To address the structural complexity and limited compliance of traditional rigid robotic wrists, as well as the absence of adjustable stiffness in soft wrists designed primarily for flexibility, a two-degree-of-freedom (2-DOF) pneumatic flexible wrist with controllable braking torque was developed. The wrist comprises three circumferentially arranged pneumatic actuators connected in parallel around a central pneumatic cross-hinge brake, enabling multidirectional pivoting, while the braking torque can be adjusted according to task requirements for pose stabilization. This configuration combines the high stiffness required for posture maintenance during braking with compliant actuation during motion. Theoretical models of the wrist pivot angle, pivoting direction, and braking torque were established. The pivot-angle model was empirically calibrated using the measured pivot-angle data, while the pivoting-direction and braking-torque models were validated experimentally. Mechanical performance was evaluated under constant-friction-torque and constant-pivot-angle conditions, and empirical relations were obtained by fitting the experimental data. A three-dimensional motion-capture system was also used to characterize the dynamic response under different braking conditions and excitation signals. Under the present experimental conditions, the results show that the wrist exhibits high compliance and enables continuous omnidirectional pivoting with a maximum single-axis pivot angle of 45.2°. The pneumatic cross‑hinge brake achieves multidirectional braking with continuously adjustable torque, reaching a maximum braking torque of 0.842 N·m under brake-only actuation at 0.35 MPa. During coordinated actuation–braking operation, the wrist’s overall resistance to external loads increased by a factor of 4.98 compared with its unpressurized initial state. This composite load-resisting capacity originates from the combined effects of the pneumatic actuators and the central brake.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

RoboticsWristWrist JointTorqueEquipment DesignHumansBiomechanical PhenomenaModels, Theoretical

Autor:innen und Institutionen

  • Engineering Training Center, Beihua University, Jilin, Jilin, China.
  • School of Mechanical Engineering, Beihua University, Jilin, Jilin, China.

ORCID-Profile: Hongbo Liu

Förderung

  • Jilin Province Science and Technology Development Program

Zitieren

APA

Liu, H., Wang, S., & Xu, W. (2026). Design, modeling, and performance analysis of a 2-DOF pneumatic flexible wrist with controllable braking torque. PLOS One, 21(11), e0362364. https://doi.org/10.1371/journal.pone.0362364

Vancouver

Liu H, Wang S, Xu W. Design, modeling, and performance analysis of a 2-DOF pneumatic flexible wrist with controllable braking torque. PLOS One. 2026;21(11):e0362364. doi:10.1371/journal.pone.0362364

BibTeX
@article{Liu2026,
  author = {Liu, Hongbo and Wang, Shuo and Xu, Wenpeng},
  title = {Design, modeling, and performance analysis of a 2-DOF pneumatic flexible wrist with controllable braking torque},
  journal = {PLOS One},
  year = {2026},
  volume = {21},
  number = {11},
  pages = {e0362364},
  doi = {10.1371/journal.pone.0362364}
}
Kostenlos starten →