EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Geometry and cooling effects on an induction self-heating insert for rapid mold temperature control: Experimental, Multiphysics, and artificial neural network-based analysis

Thanh Trung Do, Tran Minh The Uyen, Pham Son Minh iD

PLOS One · 2026

DOI: 10.1371/journal.pone.0359849 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, 2026. Verfasst von Thanh Trung Do und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, HCM City University of Technology and Engineering, Ho Chi Minh City, Vietnam. Hauptthemen laut MEDLINE: Neural Networks, Computer, Heating. Die Arbeit nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bộ Giáo dục và Ðào tạo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Control of mold-cavity surface temperature strongly affects filling, premature frozen-layer formation, and cycle time in thin-wall injection molding. This study evaluates an induction self-heating insert with a thin heating zone directly coupled to a cooling layer using experiments, a sequentially coupled electromagnetic-thermal model, and an Artificial Neural Network (ANN). The design space contains 25 Taguchi L25 geometries defined by T, W, and L; X and Y coordinates are added so that the ANN predicts the surface temperature field. Three cooling states are considered: No Water (NW), Stagnant Water (SW), and Flowing Water (FW). Experimental ANN targets are the mean of five repeated tests. The simulation reproduced the location of the hot zone; among four cases with reported quantitative differences, three differed by no more than about 10 °C and one showed a peak difference of about 20 °C. To prevent data leakage, all 846 points from each geometry were kept together during geometry-wise validation. The resulting R² values were 0.746, 0.653, and 0.493 for NW, SW, and FW, with Root Mean Square Error (RMSE) values of 17.03, 12.97, and 12.62 °C, respectively. The effects of T, W, and L depended on the cooling state and were not consistently monotonic. A proof-of-concept molding test showed complete filling of a Chip 2 part using Low-Density Polyethylene (LDPE); the mean spacing was 28.6 µm for a nominal 30 µm, and the mean height was 106.6 µm for a nominal 100 µm. These results show that combining insert geometry, cooling-water state, and a surrogate model can support local thermal design, delay frozen-layer formation, and improve filling in injection molding.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Neural Networks, ComputerHeatingTemperatureHot TemperatureCold Temperature

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, HCM City University of Technology and Engineering, Ho Chi Minh City, Vietnam.

ORCID-Profile: Pham Son Minh

Förderung

  • Bộ Giáo dục và Ðào tạo

Zitieren

APA

Do, T. T., Uyen, T. M. T., & Son Minh, P. (2026). Geometry and cooling effects on an induction self-heating insert for rapid mold temperature control: Experimental, Multiphysics, and artificial neural network-based analysis. PLOS One. https://doi.org/10.1371/journal.pone.0359849

Vancouver

Do TT, Uyen TMT, Son Minh P. Geometry and cooling effects on an induction self-heating insert for rapid mold temperature control: Experimental, Multiphysics, and artificial neural network-based analysis. PLOS One. 2026. doi:10.1371/journal.pone.0359849

BibTeX
@article{Do2026,
  author = {Do, Thanh Trung and Uyen, Tran Minh The and Son Minh, Pham},
  title = {Geometry and cooling effects on an induction self-heating insert for rapid mold temperature control: Experimental, Multiphysics, and artificial neural network-based analysis},
  journal = {PLOS One},
  year = {2026},
  doi = {10.1371/journal.pone.0359849}
}
Kostenlos starten →