EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Equivalent-circuit-based multi-objective parameter design and Pareto analysis of an LCC-S wireless power transfer system

Gang Zhou, Shishi Liao, Qi Jiang iD

PLOS One · 2026

DOI: 10.1371/journal.pone.0355130 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS One, 2026. Verfasst von Gang Zhou und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Computer Science, Sichuan University Jinjiang College, Meishan, China. Hauptthemen laut MEDLINE: Wireless Technology, Electric Power Supplies. Die Arbeit nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Sichuan University Jinjiang College 2026 Young Faculty Research Fund Project, Open Research Fund of Intelligent Digital Media Technology Key Laboratory of Sichuan Province, University of Electronic Science and Technology of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Parameter selection in an LCC-S compensated wireless power transfer system is difficult because the circuit variables are coupled and an increase in output power does not necessarily lead to higher transmission efficiency. In this study, the primary compensation inductance, equivalent load resistance, and mutual inductance were treated as three design variables, and their selection was formulated as a two-objective optimization problem. The search was performed using an archive-based particle swarm optimization method that combines dynamic inertia adjustment, probabilistic velocity pausing, and stagnation reset. MOPSO, NSGA-II, and MOGWO were used as comparison methods in 10 independent runs. Hypervolume, Spacing, the number of nondominated solutions, and runtime were recorded. Relative to MOPSO, the proposed method increased mean hypervolume by 8.45%, reduced Spacing by 41.14%, and reduced the observed MATLAB runtime by 26.30%. The obtained Pareto front contained candidates corresponding to a high-output-power boundary, an intermediate power–efficiency trade-off, and high-efficiency operation. Three representative candidates were further examined using a switching-level Simulink model together with model-calculated current and loss indicators. These results are intended to support preliminary parameter selection for LCC-S systems; hardware calibration is still required before the reported candidates can be used as practical operating points.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Wireless TechnologyElectric Power SuppliesParticle Swarm OptimizationModels, TheoreticalAlgorithmsEquipment Design

Autor:innen und Institutionen

  • School of Computer Science, Sichuan University Jinjiang College, Meishan, China.
  • School of Electrical and Electronic Information Engineering, Sichuan University Jinjiang College, Meishan, China.
  • Intelligent Digital Media Technology Key Laboratory of Sichuan Province, Chengdu, China.

ORCID-Profile: Qi Jiang

Förderung

  • Sichuan University Jinjiang College 2026 Young Faculty Research Fund Project
  • Open Research Fund of Intelligent Digital Media Technology Key Laboratory of Sichuan Province, University of Electronic Science and Technology of China

Zitieren

APA

Zhou, G., Liao, S., & Jiang, Q. (2026). Equivalent-circuit-based multi-objective parameter design and Pareto analysis of an LCC-S wireless power transfer system. PLOS One. https://doi.org/10.1371/journal.pone.0355130

Vancouver

Zhou G, Liao S, Jiang Q. Equivalent-circuit-based multi-objective parameter design and Pareto analysis of an LCC-S wireless power transfer system. PLOS One. 2026. doi:10.1371/journal.pone.0355130

BibTeX
@article{Zhou2026,
  author = {Zhou, Gang and Liao, Shishi and Jiang, Qi},
  title = {Equivalent-circuit-based multi-objective parameter design and Pareto analysis of an LCC-S wireless power transfer system},
  journal = {PLOS One},
  year = {2026},
  doi = {10.1371/journal.pone.0355130}
}
Kostenlos starten →